Holzstar KSO 790 Owner'S Manual Download Page 3

guard or other part that is damaged should be properly repaired or replaced. 

21.  NEVER  LEAVE  MACHINE  RUNNING  UNATTENTED  Turn  power  “OFF”.  Do  not  leave 

the tool until it comes to a complete stop. 

22. DIRECTION OF FEED Always feed the workpiece into the blade against the rotation of 

blade or cutters. 

23. DRUGS, ALCOHOL AND MEDICATION Never operate tools while under influence of 

drugs, alcohol, or after taking medication. 

WARNING:  For  Your  Own  Safety  Read  Instruction  Manual  Before  Operating  Tool.  Wear 

Eye  Protection.  Feed  workpiece  against  rotation  of  sanding  belt.  Do  not  use  awkward 

hand  position.  Keep  fingers  away  from  revolving  sanding  belt.  Use  fixtures  when 

necessary. 

SPECIFICATION:

 

Belt size………………………………………………………2000mm x 152mm(79” x 6”) 

Belt speed………………………………………………………………11M/sec. (34ft/sec.) 

Motor speed……………………………………………………………………..…2900RPM 

Maximum sanding length……………………………………………..……...790mm(31”) 

Round end roller diameter……………………………….…………………70mm(2 3/4”) 

Table size:    Front table…………… ……………….…790mm x 221mm(31” x 8-3/4”) 

                        Side table ………………………………..514mm x 221mm(20” x 8-3/4”) 

Vertical adjusting of front table……………………………..……………….110mm(4”) 

Table tilt……………………………………………………………………………45 degree 

Table height…………………………………………………..….…………….810mm(32”) 

Dust chute diameter..………………………………………………………….100mm(4”) 

Stand height……………………………………………………………..…..….600mm(23”) 

Net weight…………………………………………………………………….78kgs(172lbs) 

Gross weight…………………………………………………………………..90kgs(198lbs) 

Packing size(carton)……………………………104cm x 54cm x 41cm(41” x21’ x16”) 

The  specifications  dimensions  are  not  binding.  Our  firm  reserves  the  right  to  make 

changes for improvement and technical reasons. 

ASSEMBLY 

Due  to  packaging  requirements,  your  belt  sander  is  partly  assembled.  Please  do  not 

operate this belt sander before it is completely assembled and all bolts are completely 

secured. The number shown in bracket is the part number. 

Please refer to the assembly diagram A (or B if needed) to assembly the belt sander. The 

following are the steps to complete the assembly of the belt sander. 

 

Step 1:    Assemble the stand. Please note that the short bars(#95) are always ride on the 

long bars(96#) and the bolt holes are always aligned. 

Step 2: Put the main assembly on the stand and fix it on the stand with 4 bolts(#92) and 4 

screws(93). 

Step 3: Attach the long (front) table to the Main assembly. Insert the U-bar(#85) into the 

two slot on the supporting frame of the table. Then insert the U-bar with the table into the 

slots on the main assembly. Both end of the U-bar must be penetrated through the two 

holes behind the main assembly. Insert a pin(#84) into the pin hole at each end of the 

U-bar. 

Step 4: Attach the short(side) table to the Main assembly with the four bolts(#7) and four 

Summary of Contents for KSO 790









Reviews: