Fig5
1) The sight has been
zeroed at the factory.
mechanically
2) The elevation adjust
is
of the sight
ment
on the right side
(battery side). The windage adjustment is
the left side of
on
the housing (button side). Adjustment can be performed
using the supplied tool (see Fig ).
6
3) 0.5 MOA Windage & Elevation adjustments per click.
4)
0.5
Each adjustment click has a value of approximately
MOA or 1/2- inch at 100 yards (1/4" at 50y; 1/8" at 25y).
When zeroing at 50 yards, if your impacts are 2 inches low
and 1 inch right, you will need to
adjust Elevation 8 clicks UP
(clockwise) and Windage 4 clicks LEFT (counterclockwise).
5) The maximum adjustment range is ±50MOA.
AEMS CORE-110101
AEMS CORE-120101
Holosun Technologies Inc.
www.holosun.com
Customer Service
We provide a limited lifetime warranty from the date of
purchase on parts and workmanship to the original
purchaser. At our sole discretion, we will repair or replace
products found to be defective under normal use without
charge, excluding any delivery costs, which will be born by
purchaser. We will not be liable for incidental,
consequential, or special damages arising out of or in any
connection with the use or performance of this product. This
warranty is void if the product has been misused, modified,
neglected, or disassembled prior to its return. Please refer to
www.holosun.com for current and complete warranty
information and other conditions.
This device is a precision instrument that deserves
reasonably cautious care. The following tips are provided to
ensure a long product life. The optical lenses are multicoated
optical glass. When cleaning the lenses, blow away any dust
on the surface, wet the lens with lens cleaner or clean water,
then wipe away smudges with lens tissue, soft cotton or a
microfiber cloth. Avoid touching the glass surface with dry
cloth or tissue paper. Do not use organic solvents such as
alcohol or acetone. No special maintenance is needed for the
housing surface. Do not try to dismantle the device as the
internal parts are specially cleaned and sealed and with an
anti-fog treatment. Any such attempt will void the warranty.
Phone:
(909) 594-2888
Fax:
(909) 598-4888
E-mail:
Zero Setting
Maintenance & care
Limited warranty
Fig 6
Caution:
If you feel the knobs can no longer be rotated, you
may have reached the mechanical limit of the adjustment
turret. Do not try to rotate the knobs further if you feel a
bind or you may cause damage.
Sight Operation
3
4
1.Switch on:
Press and release either brightness button
("+"or"-") to turn on the sight, See Fig 5.
2.Power off:
Press the"+"and"-" buttons simultaneously to
turn the power and motion sensor off (this will disable Shake
Awake).
3.Operation mode:
Brightness adjustment: There are 12 reticle brightness
setting levels in manual mode. Settings 1 and 2 are NV
compatible and setting 12 is the brightest. Press ”+” or ”-” to
increase or decrease the brightness.
4. Sleep timer setting:
1) Please note that your red dot will automatically enter into
sleep mode after 10 minutes of no movement.
2) The sight will instantaneously wake up and turn on with
any motion detected to the last saved settings.
3) The default sleep timer setting is 10 min, but can be
changed to one of four total settings.
i. Press and hold the “+” button for 10 seconds to enter time
adjustment mode. There are 4 options: 10 min, 1h, 12h or the
sleep mode is disabled.
ii. Press and release either “+” or “-” button to set the time.
The LED will blink (1=10 min, 2=1h, 3=12h, or 4=disable sleep
mode).
iii. Press the “+” and “-” buttons simultaneously to save the
time setting and power off the sight.
5. Note:
1) Memory function: The sight will remember the last saved
brightness setting when powered on and off.
2) Low battery Warning: If the battery voltage is below
2.2Vdc, the reticle will blink slowly.
Ver:A0
Brightness
Increase
Brightness
Decrease
Windage
Adjustment
Elevation
Adjustment
Advanced Enclosed
Micro Sight
For more information about Holosun, our Terms of Use and
Sale, and our Privacy Policy, please visit holosun.com.
If you run out of adjustment range, contact your gunsmith or
Holosun for assistance.