P L E A S E R E A D A N D S AV E T H E S E
I M P O RTA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
OPERATING INSTRUCTIONS
1. Set fan on a dry, level surface.
2. Plug cord into any standard 120 volt AC outlet. Please
make sure the speed control is in the Off (0) position.
3. The power and speed control can be adjusted by
turning the speed control knob on the fan stem to the
desired settings: 1-2-3-4-5-0
4. The Oscillation Knob is located on the top of the Fan
Motor Housing. To start Oscillation, push Oscillation Knob
down. To stop Oscillation, pull Oscillation Knob up.
ADJUSTMENT INSTRUCTIONS
Fan Head Tilt Adjustment
To adjust the angle of the fan head simply move the fan
head manually to the desired angle, you will hear clicks
for each angle move.
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan. Please remember:
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
visit our website at www.holmesproducts.com for
information on how to order a new fuse. Follow the below
instructions to replace the fuse on the plug.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover down towards the prongs.
NOTE:
Ensure that fuse
cover is completely open
before attempting to
remove fuse.
3. Remove fuse carefully by
using a small screwdriver
to pry the fuse out of the
compartment by the metal
ends of the fuse. (see
Figure 2)
4. Place plug on a solid, flat surface. Insert new 5 Amp,
125 Volt fuse into fuse compartment and use a small
screwdriver to secure the metal ends of the fuse into
the compartment.
CAUTION:
Risk of fire. Replace fuse only with 5
Amp, 125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the fuse.
6. Risk of fire. Do not replace attachment plug. Contains
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
FAN CLEANING
• Always unplug the fan before cleaning or
disassembling.
• Do not allow water to drip on or into the Fan Motor
Housing.
• Use a soft cloth moistened with a soap solution to
carefully clean the front and rear grills.
• Do not use any of the following as a cleaner:
gasoline, thinner, or benzene.
ASSEMBLY INSTRUCTIONS
(See Figure 1)
NOTE:
MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.
No tool is required for assembly.
Assembly time:
5-10 minutes.
1. Pull power cord through the base and insert the lower
end of the fan stem into the centre hole of the base
until locked in place.
Note:
the back of the fan base
will have a channel for the cord to pass through.
2. Line up the slots of the rear grill with the notches on
the motor housing assembly.
3. Secure rear grill to motor housing assembly with rear
grill mounting nut. Turn clockwise to tighten.
4. Slide fan blade over motor shaft.
5. Secure fan blade to motor shaft with the blade cap.
Turn counter-clockwise to tighten.
6. Center the front grill by aligning the Holmes
®
trademark logo on the logo plate so it is horizontal
and parallel with the floor. Snap the front grill into
the grill ring. Then, holding the front grill against the
rear grill, push the grill ring into place at the top and
bottom of the fan. (Push directly on the grill ring, not
on the grills themselves). Finish securing the grill ring
in the same manner until both grills are joined
underneath the ring.
7. Close the grill ring with the grill lock located at the
bottom of the grill ring.
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
return to an authorized service facility for
examination and/or repair.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all
parts properly in place.
17. This product is intended for household use ONLY and
not for commercial or industrial applications.
18.
WARNING:
To reduce the risk of electrical shock
and injury to persons, do not use in window.
19.
WARNING:
To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
20. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse
blows, a short circuit may be present and the product
should be discarded or returned to an authorized
service facility for examination and/or repair.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
A. Front Grill
B. Grill Ring
C. Blade Cap
D. Fan Blade
E. Rear Grill Mounting Nut
F. Rear Grill
G. Motor Shaft
H. Oscillation Knob
I. Motor Housing
J. Speed Control Knob
K. Power Cord
L. Base
A
B
C
D
E
K
L
F
J
I
H
G
Figure 1
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
Figure 2
Fuse
Metal ends
Fuse cover
HDF12235_15EM1.indd 2
2/4/15 9:28 AM