HOLLEY VR2 FUEL PUMPS
P/N 12-3000 & 12-3000-2
Installation Instructions 199R10975
WARNING! THESE INSTRUCTIONS MUST BE READ AND FULLY UNDERSTOOD BEFORE BEGINNING INSTALLATION.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN POOR PERFORMANCE, VEHICLE DAMAGE,
PERSONAL INJURY, OR DEATH. IF THESE INSTRUCTIONS ARE NOT FULLY UNDERSTOOD, INSTALLATION
SHOULD NOT BE ATTEMPTED. PLEASE CONSULT HOLLEY TECH SERVICE OR A QUALIFIED MECHANIC.
NOTE:
DESIGNED FOR GASOLINE AND INTERMITTENT NON-HIGHWAY USE WITH METHANOL & E85.
APPLICATIONS:
Naturally
Aspirated
Forced
Induction
Inlet
Outlet
Inlet
Outlet
Return
Pre
Post
Pre
Post
Carb
EFI
12-3000
Yes
Street/Strip
Race
Pump Gas,
Race Gas,
Methanol*,
E-85*
323@ 8 PSI
276@ 43 PSI
254@ 60 PSI
169 @ 130 PSI
4800
4400
4000
3000
3600
3350
3200
2300
-16AN
-10AN
-16AN
-10AN
-8AN
162-577
162-576
162-577
162-575
12-852
12-865
12-851
12-864
38 Amps
12-3000-2
Yes
Street/Strip
Race
Pump Gas,
Race Gas,
Methanol*,
E-85*
323@ 8 PSI
276@ 43 PSI
254@ 60 PSI
169 @ 130 PSI
4800
4400
4000
3000
3600
3350
3200
2300
-10AN
(qty 2)
-10AN
-10AN
(qty 2)
-10AN
-8AN
162-577
162-576
162-577
162-575
12-852
12-865
12-851
12-864
38 Amps
Minimum Recommended
Line Size
Fuel Filter
(Carbureted)
Fuel Filter
(Fuel injected)
Recommended
Regulator
*Compatible for methanol and E85 for competitive drag race use only- when draining and flushing after each race event
** HP estimates are based on gasoline. Estimates calculated at 18.5V and at .5 BSFC NA and .65 BSFC FI. Individual systems will vary based on fuel system design, regulator type, fuel cell location, launch G’s, etc.
Max Amp
Draw
The pumps below do not have an internal bypass. A bypass style regulator and return line are required.
Part
Number
Compatible
up to 18.5V
Application
Fuel
Compatibility
GPH Flow at
Rated PSI
and 13.8V
Holley Recommendations for Peak Performance
Max HP**
Pump Fitting Size
PARTS REQUIRED FOR INSTALLATION:
One Pre-Filter for the 12-3000 & two Pre-Filters for the 12-3000-2.
Post-Filter
Relay Kit (30amp minimum)
– Holley P/N 12-753 or equivalent
Fuel hose and fittings (12-3000 has a single -16AN O-ring Inlet and a single -10AN O-ring Outlet)
(12-3000-2 has dual -10AN O-ring Inlets and a single -10AN O-ring Outlet)
Wire & connectors
Mounting hardware
NOTE:
These pumps are not serviceable in the field. Contact Holley tech service for fuel pump service.
INTRODUCTION:
Congratulations on your purchase of the
Holley VR2 Fuel Pump.
This instruction sheet contains all the information needed to install
this fuel pump. Please read all the
WARNINGS
and
NOTES
. They contain valuable information that can save you time and money.
Holley Performance Products cannot and will not be responsible for any alleged or actual engine or other damage, or other conditions
resulting from misapplication of the fuel pumps and fuel pressure regulators described herein. However, it is our intent to provide the
best possible products for our customer; products that perform properly and satisfy your expectations. Should you need information or
parts assistance, please contact Technical Service at 1-270-781-9741, M-F, 8 a.m. to 6 p.m. & Sat. 9 a.m. to 3 p.m. CST. Please have
the P/N ready when calling.
NOTE:
A screen type pre-filter (100 micron), a top quality post fuel filter, fuel hose and clamps, 12 gauge wire, fuel fittings, assorted
terminals and a relay kit (P/N
12-753
) is required to complete the installation of the Holley VR2 fuel pump. These parts are not
included with the fuel pump.
NOTE:
These Holley VR2 fuel pumps require the use of a bypass style fuel pressure regulator (P/N
12-852
for the 2-port &
12-865
for
the 4-port) for carbureted applications and (P/N
12-851
for the 2-port &
12-864
for the 4-port) for EFI applications.
NOTE:
The Holley VR2 fuel pump utilizes o-ring sealed inlet/outlet ports. These ports are not pipe thread, therefore
DO not use
thread sealant.
PUMP MOUNTING AND INSTALLATION:
The best location for mounting any electric fuel pump is the rear of the vehicle, near the fuel tank and in a position even with or below
the bottom of the tank, allowing the fuel to be gravity fed to the pump.
The pump should be mounted on a solid member, such as
the chassis, with the pump outlet pointing forward.
Avoid exposure of the pump and fuel lines to moving parts and to any hot
areas, such as the exhaust manifold. The pump should not be m
ounted in an enclosed area, such as the vehicle’s trunk. Follow the
steps below for mounting the pump.
Summary of Contents for 12-3000
Page 10: ...10 Fuel Pump Template...
Page 11: ...11 Controller Template...
