background image

 

 

User Manual 

 

Version 1.0                                                                                                                           4 
 

conformance with said published specifications; provided that Buyer shall (a) promptly notify the 

Company in writing upon the discovery of any defect, which notice shall include the product 

model and serial number (if applicable) and details of the warranty claim; and (b) after the 

Company's review, the Company will provide Buyer with service data and/or a Return Material 

Authorization ("RMA"), which may include biohazard decontamination procedures and other 

product-specific handling instructions, then, if applicable, Buyer may return the defective 

Products to the Company with all costs prepaid by Buyer. Replacement parts may be new or 

refurbished, at the election of the Company. All replaced parts shall become the property of the 

Company. Shipment to Buyer of repaired or replacement Products shall be made in accordance 

with the Delivery provisions of the Terms & Conditions agreed to by the purchase of this 

product. Consumables are expressly excluded from this warranty.  

Notwithstanding the foregoing, Products supplied by the Company but not manufactured by the 

Company are not warranted by the Company, and the Company disclaims all warranties 

associated with the accuracy of any original manufacturer or third-party supplier Product 

information, but the Company agrees to assign to Buyer any warranty rights in such Product 

that the Company may have from the original manufacturer or third-party supplier, to the extent 

such assignment is allowed by such original manufacturer or third-party supplier. 

In no event shall the Company have any obligation to make repairs, replacements or corrections 

required, in whole or in part, as the result of (i) normal wear and tear, (ii) accident, disaster or 

event of force majeure, (iii) misuse, fault or negligence of or by Buyer, (iv) use of the Product in 

a manner for which they were not designed, (v) causes external to the Product such as, but not 

limited to, power failure or electrical power surges, (vi) improper storage and handling of the 

Product or (vii) use of the Product in combination with equipment or software not supplied by the 

Company. If the Company determines that Product for which Buyer has requested warranty 

services are not covered by the warranty hereunder, Buyer shall pay or reimburse the Company 

for all costs of investigating and responding to such request at the Company's then prevailing 

time and materials rates. If the Company provides repair services or replacement parts that are 

not covered by this warranty, Buyer shall pay the Company therefor at the Company's then 

prevailing time and materials rates.  

ANY INSTALLATION, MAINTENANCE, REPAIR, SERVICE, RELOCATION OR ALTERATION 

TO OR OF, OR OTHER TAMPERING WITH, THE PRODUCT PERFORMED BY ANY 

PERSON OR ENTITY OTHER THAN THE COMPANY WITHOUT THE COMPANY'S PRIOR 

WRITTEN APPROVAL, OR ANY USE OF REPLACEMENT PARTS NOT SUPPLIED BY THE 

COMPANY, SHALL IMMEDIATELY VOID AND CANCEL ALL WARRANTIES WITH RESPECT 

TO THE PRODUCT. 

Summary of Contents for 10310001

























Reviews: