manualshive.com logo in svg

HODAKA HODAKATEST HT-1300Z, User Manual, Page: 11 / 17

Share
Download
HODAKA HODAKATEST HT-1300Z User Manual Download Page 11

8.2.9　　Zero setting

8.3　　Operation - Stored data menu
8.3.1　　Stored data menu

：Move cursor

8.3.1.1　View stored No.

：Select 「Zero setting」, confirm it.

：Move cursor

Next window.

：Select 「View stored sites」, and confirm it.
Next window

：next window

：Select stored sits.

：Move to 「8.3.2　Delete stored sites」

For zero setting, it takes about 30 seconds.

：Next window

During zero setting, below mark is indicated.

calibration mark.

：4 lines/8 lines, indication change

：Chang page

：Next window

：Print out

：Next window (boiler temperature / soot no.)

"Oily" is appeared if you select "YES"at Smoke no.

：Move to stored sites selection window

19

20

In case you do not press Okay, after  about 8 seconds, it
automatically  move to next window.

：Switch it measurement menu window. During zero setting, you
can set other parameters and see stored data.

Left window is appeared only if you select "YES" at Boiler
temp?/Smoke no.?  of 「8.4.1.1　Unit　setting」

Notice

Please wait…

Pr

Delete stored 

Yes                No

Notice Zero setting must be determined in ambient air. 

Summary of Contents for HODAKATEST HT-1300Z


















Reviews:

No comments