- 2 -
140 58th St.
Overview:
The FN-400ULX is a power supply that converts a 115VAC / 60Hz input to a 12VDC or 24VDC regulating output
(see specifications below)
.
Agency Listings:
•
UL File # S4707:
UL Listed for Access Control
Specifications:
Altronix Corp .
Output
(cont’d)
:
•
Short circuit and thermal overload protection.
Battery Backup:
System Units (UL 294), UL Listed Standard for Power
Supplies for Use with Burglar-Alarm Systems (UL 603),
UL Listed Hospital Signaling and Nurse Call Equipment
(UL 1069), UL Listed Standard for Safety for Fire
Protective Signaling Systems (UL 1481).
•
MEA - NYC Department of Buildings Approved.
•
CSFM - California State Fire Marshal Approved.
•
FM Approved.
Input:
•
Input 115VAC, 60Hz, 3 amp.
•
AC input and DC output LED indicators.
Output:
•
Class 2 Rated power-limited output.
•
12VDC or 24VDC selectable output.
•
4 amp total supply current at 12VDC
or 3 amp total supply current at 24VDC.
•
Filtered and electronically regulated outputs.
•
Built-in charger for sealed lead acid or gel type batteries.
•
Automatic switch over to stand-by battery when
AC fails.
•
Maximum charge current 0.7 amp.
•
Zero voltage drop when switched over to battery backup.
Supervision:
•
AC fail supervision (form “C” contacts).
•
Low battery supervision (form “C” contacts).
•
Battery presence supervision (form “C” contacts).
Additional Features:
•
Power supply, enclosure, cam lock and battery leads.
Enclosures:
FN-400ULX-R (Red)
FN-400ULX-C (Charcoal Grey)
Enclosure Dimensions
(H x W x D)
:
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
Power Supply Voltage Output Selections:
Switch Detail
OPEN SWITCH
Fig. 1
CLOSED SWITCH
Stand-by Specifications:
Output
4 hr. of Stand-by &
5 Minutes of Alarm
24 hr. of Stand-by &
5 Minutes of Alarm
60 hr. of Stand-by &
5 Minutes of Alarm
12VDC / 40AH Battery
Stand-by = 4.0 amp
Alarm = 4.0 amp
Stand-by = 1.0 amp
Alarm = 4.0 amp
Stand-by = 300mA
Alarm = 4.0 amp
24VDC / 12AH Battery
--------
Stand-by = 200mA
Alarm = 3.0 amp
--------
24VDC / 40AH Battery
Stand-by = 3.0 amp
Alarm = 3.0 amp
Stand-by = 1.0 amp
Alarm = 3.0 amp
Stand-by = 300mA
Alarm = 3.0 amp
Installation Instructions:
The unit should be installed in accordance with article 760 of The National Electrical Code as well as NFPA 72 and all
applicable Local Codes.
1.
Mount unit in the desired location
.
Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install two fasteners. Place the enclosure’s upper keyholes over the two upper
screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 4)
.
2.
Set the FN-400ULX to the desired DC output voltage by setting SW1
(Fig. 1, pg. 2, Fig. 2c, pg. 3)
to the appropriate
position (
refer to Power Supply Voltage Output Selections chart
).
3.
Connect AC power (115VAC 60Hz) to terminals marked [L, G, N]
(Fig. 2, pg. 3)
. Use 14 AWG or larger for all
power connections (Battery, DC output, AC input). Use 22 AWG to 18 AWG for power-limited circuits
(AC Fail/Low Battery reporting).
Keep power-limited wiring separate from non power-limited wiring (115VAC / 60Hz Input, Battery Wires).
Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.
Opened - 24V
Closed - 12V
SW1
Output
Switch Position
12VDC
SW1 - CLOSED
(Fig. 1, on right)
24VDC
SW1 - OPEN
(Fig. 1, on right)