HobbyZone APPRENTICE S Instruction Manual Download Page 24

®

Mini Apprentice

®

 S 

EN

24

Limited Warranty

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the 
product purchased (the “Product”) will be free from defects in materials and 
workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) 
damage due to acts of God, accident, misuse, abuse, negligence, commercial 
use, or due to improper use, installation, operation or maintenance, (iii) 
modifi cation of or to any part of the Product, (iv) attempted service by 
anyone other than a Horizon Hobby authorized service center, (v) Product not 
purchased from an authorized Horizon dealer, or (vi) Product not compliant 
with applicable technical regulations, or (vii) use that violates any applicable 
laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER 
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL 
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED 
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY 
ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE 
REQUIREMENTS OF THE PURCHASER’S INTENDED USE. 

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be 
that Horizon will, at its option, either (i) service, or (ii) replace, any Product 
determined by Horizon to be defective. Horizon reserves the right to inspect 
any and all Product(s) involved in a warranty claim. Service or replacement 
decisions are at the sole discretion of Horizon. Proof of purchase is required 
for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS 
WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. 

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL 
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR 
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM 
IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY 
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED 
OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the 
liability of Horizon exceed the individual price of the Product on which 
liability is asserted. As Horizon has no control over use, setup, fi nal assembly, 
modifi cation or misuse, no liability shall be assumed nor accepted for any 
resulting damage or injury. By the act of use, setup or assembly, the user 
accepts all resulting liability. If you as the purchaser or user are not prepared 
to accept the liability associated with the use of the Product, purchaser is 
advised to return the Product immediately in new and unused condition to the 
place of purchase.

Law

These terms are governed by Illinois law (without regard to confl ict of law 
principals). This warranty gives you specifi c legal rights, and you may also 
have other rights which vary from state to state. Horizon reserves the right to 
change or modify this warranty at any time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty 
support or service. Once assembly, setup or use of the Product has been 
started, you must contact your local distributor or Horizon directly. This will 
enable Horizon to better answer your questions and service you in the event 
that you may need any assistance. For questions or assistance, please visit our 
website at www.horizonhobby.com, submit a Product Support Inquiry, or call 
the toll free telephone number referenced in the Warranty and Service Contact 
Information section to speak with a Product Support representative. 

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the 
country you live and use the Product in, please use the Horizon Online Service 
Request submission process found on our website or call Horizon to obtain a 
Return Merchandise Authorization (RMA) number. Pack the Product securely 

using a shipping carton. Please note that original boxes may be included, 
but are not designed to withstand the rigors of shipping without additional 
protection. Ship via a carrier that provides tracking and insurance for lost or 
damaged parcels, as Horizon is not responsible for merchandise until it arrives 
and is accepted at our facility. An Online Service Request is available at http://
www.horizonhobby.com/content/_service-center_render-service-center. If you 
do not have internet access, please contact Horizon Product Support to obtain 
a RMA number along with instructions for submitting your product for service. 
When calling Horizon, you will be asked to provide your complete name, street 
address, email address and phone number where you can be reached during 
business hours. When sending product into Horizon, please include your RMA 
number, a list of the included items, and a brief summary of the problem. A 
copy of your original sales receipt must be included for warranty consideration. 
Be sure your name, address, and RMA number are clearly written on the 
outside of the shipping carton. 

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with 
a LiPo battery, please contact the appropriate Horizon Product Support 
offi ce.

Warranty Requirements 
For Warranty consideration, you must include your original sales receipt 
verifying the proof-of-purchase date.

 Provided warranty conditions have 

been met, your Product will be serviced or replaced free of charge. Service or 
replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service
Should your service not be covered by warranty, service will be 
completed and payment will be required without notifi cation or estimate 
of the expense unless the expense exceeds 50% of the retail purchase 
cost

. By submitting the item for service you are agreeing to payment of the 

service without notifi cation. Service estimates are available upon request. You 
must include this request with your item submitted for service. Non-warranty 
service estimates will be billed a minimum of ½ hour of labor. In addition you 
will be billed for return freight. Horizon accepts money orders and cashier’s 
checks, as well as Visa, MasterCard, American Express, and Discover cards. 
By submitting any item to Horizon for service, you are agreeing to Horizon’s 
Terms and Conditions found on our website http://www.horizonhobby.com/
content/_service-center_render-service-center. 

ATTENTION: Horizon service is limited to Product compliant in the country 
of use and ownership. If received, a non-compliant Product will not be 
serviced. Further, the sender will be responsible for arranging return 
shipment of the un-serviced Product, through a carrier of the sender’s 
choice and at the sender’s expense. Horizon will hold non-compliant 
Product for a period of 60 days from notifi cation, after which it will be 
discarded.

10/15

Summary of Contents for APPRENTICE S





























Reviews: