Hobby King HK-TR6A Instructions Manual Download Page 10

- 10 - 

 

CARE & FEEDING OF THE HOBBY KING TX. 

 

The 

HOBBY KING

 transmitter uses 8 x AA size batteries.  Either Alkaline dry cells or rechargeables.   

We use Sanyo ENELOOP rechargeable AA cells which are guaranteed to hold 85% of their charge for 12 
months if not being used.  Always recharge them after the TX has been used for any length of time. 
It is most important to ensure the batteries always have plenty of charge in them when using the TX.   
If the LED is showing RED, the batteries are getting low.  This may result in loss of control.  If you have chosen 
to use Alkalines, we advise you to replace them immediately.   
Do not attempt to use the TX if the RED LED is lit.  Always keep a spare set of batteries handy. 

 

HOBBY KING TX PROGRAMMING. 

 

HOBBYKING R/C 

systems are provided with a CD and USB cable so that the TX can be programmed to suit 

yourself. We strongly suggest you check the settings in your TX BEFORE attempting to use the system. 
Once the USB – Serial port cable program and the 

T6config

 programs have been installed you can proceed. 

The TX must be connected to the computer and turned ON.   
Under 

SYSTEM OPTION

 select 

SETTING

 and choose a COM Port from the available list.  Press OK. 

When the program is open the operator has the following programmable features under 

SYSTEM SETTING

END POINT:

 ALL 100%. 

REVERSE:

 

ALL NORMAL. i.e. Leave the boxes 

unticked

SUB TRIM:

 ALL 

ZERO. 

DR:

 ALL 

ZERO. 

STICK:

 

SELECT CORRECT STICK MODEL: = MODE #1 or MODE # 2.  

(MOST IMPORTANT).

 

TYPE:

 SELECT 

ACRO. 

MIX:

 

MIX # 1: SWITCH OFF.  Or set it to throttle cut with Switch B. 

 

MIX # 2: Source = VRA.  DES = CH 5.  UP = 100%.  DN = 100%.  SWITCH = ON. 

 

MIX # 3: Source = VRB.  DES = CH 6.  UP = 100%.  DN = 100%.  SWITCH = ON. 

Always press 

OK

 after each step. 

SAVE

 = saves the programmed settings in the TX to a file in your computer. 

OPEN

 = opens the saved settings filed in your computer so they can be uploaded into a different TX. 

Instructions on how to set up and operate the COPTERX 6 channel R/C are available here: 

 

http://www.helipro-rc.com/download/RADIO%20MANUAL.pdf

 

CAUTION:  BIG FILE  9.10 Meg 

 

Summary of Contents for HK-TR6A











Reviews: