Hobart Ecomax 502L Installation And Operation Instructions Manual Download Page 9

 9

4. 

START-UP

 

Attention:

  

The maximum suction head of the dosing pumps is 1.5 m. Do 

not confuse the containers 

Use only detergent and rinse aid for commercial applications. 

Please pay attention to the manufacturer’s safety instructions.

NOTE: 

Before changing to a different product type (even from the  

same supplier), the suction hoses must be rinsed thoroughly 

with fresh water (procedure as described under section 

4.3.). Otherwise, the mixing of different types of chemicals 

will cause crystallization, which may result in a malfunction 

of the dosing pump.

4.1.  DETERGENT PUMP (OPTIONAL)

 

Do not use any acidic detergent products with the optional built-in 

detergent pump! (The ph-value has to be higher than 7.)

 

Place the suction hose into the external detergent container.  

Fill the suction hose according to chapter section 4.3.

4.2.  RINSE AID PUMP (OPTIONAL)

 

Place the suction hose (blue marking) into the external rinse aid 

container. Fill the suction hose according to chapter section 4.3.

Summary of Contents for Ecomax 502L
























Reviews: