HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 60 / 92

9 »Motion Manager« software (optional)

Operation manual mzr-4622

Technical data subject to change without prior notice!

Last update: March 2019

»Motion Manager« software (optional)

The »Motion Manager« software enables operation and configuration of the

drive and offers a possibility of an online graphic analysis of the operating data.

The software is delivered on CD. The program may be installed on a PC running

under Windows 7

, Windows 8 or Windows 8.1

operating systems.

Install the software »Motion Manager« by starting the program »Setup« from

the CD.

If the »Motion Manager« CD are not available, and you have received for

example the »mzr-pump control« software, you may still download this

program from the web site http://www.hnp-mikrosysteme.de/download-

center.html or the web site www.faulhaber.com (menu support - download).

Here, the latest version is always available in English and German.

After the installation the »Motion Manager« program may be loaded from the

»Faulhaber Motors« folder from the Windows start menu.

In order to program the drive, the micro annular gear pump should be put into

operation. The drive should be connected to the PC with the delivered

null-modem cable.

9.1

Direct drive control

The »Motion Manager« software enables to send the input commands directly

to the drive. This allows execution of movement commands and modification of

the drive parameters. (see figure 34)

figure 34

Motion Manager software for direct control of the drive

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands