HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 16 / 92

3 Transport and intermediate storage

Operation manual mzr-4622

Technical data subject to change without prior notice!

Last update: March 2019

Transport and intermediate storage

3.1

Shipment of the pumps and protection measures

The pumps leaving the factory are secured against corrosion and shocks. The

inlets and outlets of the pumps are protected with plastic plugs in order to

prevent any foreign bodies from penetrating into the device.

3.2

Transport

In order to avoid any transport-related damage, the package must be protected

against shocks. HNP Mikrosysteme guarantees that all goods leave the factory

in the best condition. Any noticed damage should be reported to the

concerned forwarding agent, authorized dealer or to HNP Mikrosysteme

as manufacturer.

3.3

Intermediate storage

Following points concerning pump storage should be observed:

−

necessary conservation procedure (see also chapter 7.4.1)

−

the protective caps must be put on

−

the pump should not be stored in humid places

−

for storage temperature - refer to chapter 1.5 of the present manual

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands