HNC Electric SV-E3 Series, Instruction Manual

Page: 83 / 178

83
659. 0 [Special setting]
Home position
return Timeout
Time
Set Home position return Timeout Time.
[Initial value] 60,000[10ms]
[Setting range] 0 to 60,000
No
6.2 Parameter list for point table
Table 6.2.1 Parameter list for point table
Point
No.
Position
[Command
pulse]
Rotation
speed
[r/min]
Acceleration
time [ms]
Deceleration
time [ms]
Command
method [-]
Dwell time
[ms]
Running
operation [-]
Positioning
completion
[Encoder
pulse]
valid/ Invalid
[-]
0 No.722.0 No.724.0 No.726.0 No.727.0 No.720.0 No.728.0 No.720.1 No.729.0 No.720.3
1 No.742.0 No.744.0 No.746.0 No.747.0 No.740.0 No.748.0 No.740.1 No.749.0 No.740.3
2 No.762.0 No.764.0 No.766.0 No.767.0 No.760.0 No.768.0 No.760.1 No.769.0 No.760.3
3 No.782.0 No.784.0 No.786.0 No.787.0 No.780.0 No.788.0 No.780.1 No.789.0 No.780.3
4 No.802.0 No.804.0 No.806.0 No.807.0 No.800.0 No.808.0 No.800.1 No.809.0 No.800.3
5 No.822.0 No.824.0 No.826.0 No.827.0 No.820.0 No.828.0 No.820.1 No.829.0 No.820.3
6 No.842.0 No.844.0 No.846.0 No.847.0 No.840.0 No.848.0 No.840.1 No.849.0 No.840.3
7 No.862.0 No.864.0 No.866.0 No.867.0 No.860.0 No.868.0 No.860.1 No.869.0 No.860.3
8 No.882.0 No.884.0 No.886.0 No.887.0 No.880.0 No.888.0 No.880.1 No.889.0 No.880.3
9 No.902.0 No.904.0 No.906.0 No.907.0 No.900.0 No.908.0 No.900.1 No.909.0 No.900.3
10 No.922.0 No.924.0 No.926.0 No.927.0 No.920.0 No.928.0 No.920.1 No.929.0 No.920.3
11 No.942.0 No.944.0 No.946.0 No.947.0 No.940.0 No.948.0 No.940.1 No.949.0 No.940.3
12 No.962.0 No.964.0 No.966.0 No.967.0 No.960.0 No.968.0 No.960.1 No.969.0 No.960.3
13 No.982.0 No.984.0 No.986.0 No.987.0 No.980.0 No.988.0 No.980.1 No.989.0 No.980.3
14 No.1002.0 No.1004.0 No.1006.0 No.1007.0 No.1000.0 No.1008.0 No.1000.1 No.1009.0 No.1000.3
15 No.1022.0 No.1024.0 No.1026.0 No.1027.0 No.1020.0 No.1028.0 No.1020.1 No.1029.0 No.1020.3
7. Timing chart
7.1 Power ON
Figure 7.1.1 Power ON