background image

Appendix A: Regulatory Compliance

15 (18)

A

Regulatory Compliance

A.1

EMC Compliance (CE)

The product is in compliance with the Electromagnetic Compatibility Directive. More information
and the Declaration of Conformity is found at

www.ixxat.com

.

A.2

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause
undesired operation.

Product name

CAN Repeater

Model

CAN-CR100, CAN-CR110/FO, CAN-CR120/HV, CAN-CR300

Responsible party

HMS Industrial Networks Inc

Address

35 E. Wacker Dr, Suite 1700
Chicago , IL 60601

Phone

+1 312 829 0601

Any changes or modifications not expressly approved by HMS Industrial Networks could
void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

CAN FD Repeater User Manual

4.01.0210.20000 1.3 en-US

Summary of Contents for Ixxat CAN-CR100





















Reviews: