© 2022 HM Electronics, Inc. All rights reserved.
3
J3 Vehicle Detection Output
Pin # Label
Description/wire color
1
VEH_DET_OUT1
Output signal from LOOP5 (at J4)
2
VEH_DET_OUT2
Output signal from LOOP6 (at J5)
3
VEH_DET_OUT3
Output signal from LOOP7 (at J6)
4
VEH_DET_OUT4
Output signal from LOOP8 (at J7)
5
GND
6
GND
J3 is for Vehicle Detection outputs to the Base Station
to support menu detection in the absence of an ex-
ternal VDB. These outputs are from the four Onboard
detectors.
LED state table
LED
Status/Description
POWER
Solid Blue and always on if the CU is on and connected to the TSP
GREET
Solid Blue, only on when the host is speaking
EXTERNAL DETECTORS
Solid Blue, only on when a detector is connected, and a vehicle is
detected at the corresponding detection point
ON-BOARD DETECTORS
Solid Blue, only on when a detector is connected, and a vehicle is
detected at the corresponding detection point
J2 External Detector Inputs
Pin # Label
Description/wire color
1
EXT_IN1/RLY_NO
From NEXEO Base Station: J800-7 or
EOS Base Station: J1-4, +ve Menu
Det. wire. (Red wire)
2
GND/RLY_COM
From NEXEO Base Station: J800-6 or
EOS Base Station: J1-3, GND Menu
Det. wire. (Black wire)
3
EXT_IN2/RLY_NO
4
GND/RLY_COM
5
EXT_IN3/RLY_NO
6
GND/RLY_COM
7
EXT_IN4/RLY_NO
8
GND/RLY_COM
J2 supports four external detector inputs. These in-
clude both relay closure and logic-level signal inputs
in support of non-HME, wireless or generic detectors,
including positive polarity signal compatibility.
J1 Greet Inputs
Pin # Label
Description/wire color
1
From NEXEO Base Station: J800-1 or
EOS Base Station: J6-8, +ve Outside
Mic/Speaker wire. (Green wire)
2
GREET1-
From NEXEO Base Station: J800-2 or
EOS Base Station: J6-7, -ve Outside
Mic/Speaker wire. (White wire)
3
4
GREET2-
5
GND
Ground/Shield wire from either Base
Station
6
/ALT_GREET1
7
/ALT_GREET2
8
GND
J1 supports two greet signal inputs from the Base
Station. Standard greet signals received from the
audio lines (speakers) are terminated at GREET1 and
GREET2 inputs. The ALT GREET 1 & 2 inputs are for
digital inputs from other sources, such as using a
headset button. Two greet signals is the maximum
supported at the same time. Both can be from the
same source or can be a combination of two sources
such as GREET1 and ALT GREET2.
J4, J5, J6, J7 Onboard Detector Inputs
Pin # Label
Description/wire color
J4-1
Loop 5 +ve
Menu point/first detector loop in Lane
J4-2
Loop 5 -ve
J5-1
Loop 6 +ve
Additional loop after first detection point
J5-2
Loop 6 -ve
J6-1
Loop 7 +ve
Additional loop after first detection point
J6-2
Loop 7 -ve
J7-1
Loop 8 +ve
Additional loop after first detection point
J7-2
Loop 8 -ve
J4 is the default available onboard VDB for a direct
connection. Connect loop/wireless detector input
here.
In addition to accepting a direct detector connection,
these inputs (J4 - J7) can also be configured to sup-
port both relay closure and logic-level signal inputs.
J5 - J7 requires activation to use (call HME at the
phone number at the end of this guide for details).
A B 1 2 3 4 5 6 7 8
GREET
POWER
EXTERNAL DETECTORS
ON-BOARD DETECTORS
TSP60
J1 GREET
J2 EXT. DET IN J3 DET OUT
J4
LOOP5
J5
LOOP6
J6
LOOP7
J7
LOOP8
USB type B
OPENING for
CABLE ROUTING
CONNECTOR
LABELS
PCBA SN
LABEL
LED
PANEL
MOUNTING
KEYHOLE
MAGNETIC
LATCH
TSP60
FRONT VIEW
BOTTOM HALF OPENED TO EXPOSE CONNECTORS
HOLES for
CABLE TIES/
STRAIN RELIEF
Lorem ipsum
Fig. 3.1
Fig. 3.2
A copy of this guide and much more can be found by scanning
this QR code or going to:
https://www.hme.com/qsr/drive-thru-user-manuals/
HM ELECTRONICS, INC.
2848 Whiptail Loop, Carlsbad, CA 92010 USA
Phone: 1-800-848-4468 | Fax: 858-552-0172
Website: www.hme.com | Email: [email protected]
The HME logo and product names are registered
trademarks or trademarks of HM Electronics, Inc.
tsP W
IrIng
C
onneCtIons
PCBA SN Label: This serial number
identifies the TSP60 if more than
one is used. It can be found under
TSP SETTINGS>TSP60 on the
ZOOM Nitro display (see Fig. 3.2).
Connected
Reset
Remove
