© 2022 HM Electronics, Inc. All rights reserved.
PUB-00066
Rev B 05/05/22
4. Mount the monitor bracket to the wall. To do this,
find an appropriate location (preferably along a
stud if wall construction is a wood stud frame).
• Hold the wallplate level against the wall,
and mark the wall through the two mounting
holes.
• Drill holes at the marked locations.
• Mount the bracket to the wall using the nec-
essary hardware (screws and wall anchors or
toggle bolts if necessary); see Fig. 1.3.
BRACKET attached to
WALL with two screws
Fig. 1.3
5. Attach the monitor to the faceplate with the pro-
vided hardware (see Fig. 1.4).
BRACKET
attached to
MONITOR
with four screws
Fig. 1.4
I
nstallatIon
:
Tools, Equipment, & Material Required:
• General hand tools, screwdrivers, etc.
• Tape Measure, pencil/marker
• Drill with drill bit set
• Fish sticks/tape for routing cables (if necessary)
• Cable ties for bundling cables and strain relief
• Belden 8723 audio cable or equivalent
• Protective equipment such as safety glasses.
Fig. 1.1
1. Check the packing list! Verify you have received
everything listed.
2. Survey the premises with store manager to de-
termine the optimal mounting location for the
ZOOM Nitro. Take into consideration:
• User accessibility
• Appropriate space for mounting all system
components
• Proximity to a power outlet
• Cable lengths required between connections
• Clearance from obstructions like electrical
and plumbing obstructions when drilling
• Mount the system high enough on a wall to
be out of the way but still visible/accessible.
3. Remove (if attached) and discard the monitor
base stand (see Fig1.2).
Fig. 1.2
ZOOM
Nitro®
QUICK REFERENCE INSTALLATION GUIDE
6. Attach the CU to the CU wallplate using the pro-
vided hardware (see Fig. 1.5).
COM
DCIN
HDMI 1
HDMI 2
FOR SALES & SERVICE CALL:
1-800-848 4468
1
2
3
4
DCIN
HDMI 1
HDMI 2
FOR SALES & SERVICE CALL:
1-800-848 4468
CU50 Sales
& Service
Sticker
Outer
Mounting
Holes (x4)
Attach wallplate at
CU 60 rear
Fig. 1.5
7. Mount the CU on the wall.
• Hold the plated CU against the wall, and
mark the wall through the four outside
mounting holes.
• Drill holes at the marked locations.
• Mount the plated CU to the wall using the
necessary hardware (screws and wall anchors
if necessary); see Fig. 1.6
Note:
The HME Sales and Service sticker should
be right side up.
COM
DCIN
HDMI 1
HDMI 2
FOR SALES & SERVICE CALL:
1-800-848 4468
1
2
3
4
DCIN
HDMI 1
HDMI 2
FOR SALES & SERVICE CALL:
1-800-848 4468
CU60 Sales
& Service
Sticker
Outer
Mounting
Holes (x4)
Attach wallplate at
CU 60 rear
Fig. 1.6
8. Connect the cables (reference Fig. 1.7 for each
step):
1. Connect the network cable to the network
port (verify it is also connected at the network
router end).
2. Connect a mouse (and keyboard if desired)
to the USB port (see all connections in the
following diagram).
3. Connect the HDMI cable for the primary moni-
tor to the port labeled HDMI 1.
4. Connect the power adapter.
Note:
HDMI 2 is for the Drive-Thru Leaderboard
display (if desired). Remove port cap to access.
COM
DCIN
HDMI 1
HDMI 2
FOR SALES & SERVICE CALL:
1-800-848 4468
1
2
3
4
DCIN
HDMI 1
HDMI 2
FOR SALES & SERVICE CALL:
1-800-848 4468
CU60 Sales
& Service
Sticker
Outer
Mounting
Holes (x4)
Attach wallplate at
CU 60 rear
Fig. 1.7
9. Connect the power cable and the HDMI cable to
the monitor (see Fig. 1.8). Connect the other end
of the power cable to an electrical outlet.
POWER CABLE
HDMI CABLE
MONITOR REAR
Lorem ipsum
Fig. 1.8
1
2
4
8
6
3
5
9
7
