manualshive.com logo in svg

HKC 51637, Owner'S Manual, Page: 9 / 13

Share
Download
HKC 51637 Owner'S Manual Download Page 9

9

ASSEMBLY INSTRUCTIONS

Motor Screw

Blade 

Canopy

Mounting Bracket Screw

J-shaped 

slot

Round 

Hole

Black (Hot)

Wire Connector

White (Neutral)
Bare/Green (Ground)

Black

Blue

White

Green

13

14

12

11

WARNING: 

Do NOT 

wire the fan motor to a 

variable-speed (dimmer) 

wall control. 

12. Raise the canopy, ensure the two mounting bracket

screws are aligned with the J-shaped slots in the canopy.

Then turn the canopy in a clockwise direction until the

mounting bracket screws are completely engaged in

the J-shaped slots. Install the two previously removed

mounting bracket screws in the round holes. Securely

tighten all mounting bracket screws.

13. Install the blade to the top side of the motor with 

motor screws previously removed. Tighten with Phillips 

screwdriver (not included). Repeat for each blade.

11. Use wire connectors to connect the fan wires to the 

power supply wires according to the wiring diagram and 

the following instructions:

• Connect the green wire from the downrod and mounting 

bracket to the bare/green (ground) supply wire.
• Connect the white wire from the fan to the white 

(neutral) supply wire.
• Connect the black and blue wires from the fan to the 

black (hot) supply wire.

Important:

 After the connections have been made, the 

wires should be turned upward and pushed carefully 

up into the outlet box. Place the black and white wire 

connections on opposite sides of the outlet box.

14. Remove one of the three fitter plate screws 

preassembled to the fitter plate and loosen the other two 

but do not remove. Connect the 9-pin connector from

the fitter plate to the 9-pin connector from the switch 

housing. Align the keyhole slots in the switch housing with 

the loosened screws in the fitter plate. Turn switch housing 

clockwise and replace the previously removed fitter plate 

screw. Tighten all screws.

Fitter Plate Screw

Fitter Plate

Keyhole Slot

9-pin 

Connector

Switch 

Housing 

Summary of Contents for 51637














Reviews:

No comments