background image

HNV-970 Series 

   

                                                                                                                  HITROL CO., LTD.                                             

          9   

                                                                                                                                                                                         

Failure Check 
 
 
 
 
Marking 

 

 

 

                 

 

 
 
 
 
 
Warranty and 
Contact   
Information 

Warranty and Service 

The product is subject to the warranty for 2 years after shipment and unpaid service 

will be provided for any damage occurred under normal operating conditions. If it is 

not about the failure of product, service fee will be charged.   

 

Headquarter

  Factory

  R&D Institute 

Hitrol Co., Ltd. 

141, Palhakgol-Gil, Jori-Eup, Paju-Si, Gyeonggi-Do, Korea 

Tel. : +82-31-950-9700 (Headquarter and After Sales Service Team) 

Fax : +82-31-943-5600 (Headquarter and After Sales Service Team) 

  Product Identification 

The product identification mark is attached on the housing and shows the model 

name, serial number, working temperature, working pressure and matters regarding 

output. The serial number is a unique manufacturing number for the identification of 

the product.

 

      If the operating does not work normally, check first below points.   

     

  Is the power connection correct? 

     

  Is the power supplying properly in accordance with the specifications? 

 

  Is the wiring for output contact correct? 

Summary of Contents for HLC-970-L










Reviews: