background image

 

 

 

AIR COOLED WATER CHILLERS 

– AXIAL FANS 

 

EKWXA/EKWXBA 

 

11.15 207443 Rev104 

 

INTRODUCTION 

 

GENERAL DESCRIPTION 

 

► Manual purpose 

 

This manual and the 88610 and 88611 documents have been  created to guide in the correct installation, 
start-up  and  maintenance  of  the  unit.  For  this  reason  is  essential  to  read  the  instructions  paying  due 
attention.  The  manufacturer  waives  any  liability,  for  possible  damages  on  persons  or  stuff,  as  a 
consequence of an improper use of this unit and/or non-compliance with these instructions.  

 

► Manual preservation 

 

This manual and the electric diagram of the unit must be retained and remain available to the operator for 
further consultation. 

 

► Local safety standards 

 

Follow the local security standards during installation. 

 

► Electrical network 

 

Check that electrical network features are in accordance to data shown in the data nameplate of the unit. 

 

►Packaging 

 

Packaging  material  (plastic  bags,  cellular  polystyrene,  cloves,  etc.)  constitutes  a  dangerous  source,  for 
that  it  should  be  kept  out  of  the  reach  of  children  and  recycled  correctly  according  to  local  security 
standards. 

 

► Maintenance 

 

Before executing any maintenance operation, cut off the unit power supply. Operations have to be carried 
out following local security standards. 

 

► Periodic inspections 

 

Carry  out  periodic  inspections  to  detect  possible  damaged  or  broken  pieces.  If  they  are  not  repaired  it 
could result in damage to people or stuff. 

 

► Incorrect operation 

 

In case of breakdowns or operation faults, turn off unit. 

 

► Repairs 

 

Reparations should be always realized for trained personal authorized by the manufacturer using original 
spares. Failure to comply with these warnings could affect the safety features of the unit. 

 

► Modifications 

 

All manufacturer responsibility is declined when the warranty has been expired in case of electrical and/or 
mechanical  modifications.  Alterations  in  general  not  expressly  allowed  and  not  respecting  what  is 
instructed here, they cause the warranty expiration. 

 

► Use

 

The unit will only be used for the purpose it has been conceived. Any other use does not imply any kind of 
compromise or liability for the manufacturer. 

 
 
 

Summary of Contents for EKWXA

























Reviews: