Hitecsa CCHBA/CCHA 1201 Installation, Operation & Maintenance Manual Download

Page: 28 / 35

IOM_WPVBZ HE-WPVZ HE_401-1201-4002_208110_200901_EN

PACKAGED COMPACT VERTICAL

– WATER / AIR

WPVBZ HE / WPVZ HE

OPERATION

TH-TUNE CONTROLLER

DESCRIPTION OF THE ALARM CODES

CODE

DESCRIPTION

AL01

Alarm B1 probe disconnected (Outdoor temperature)

AL02

Alarm B2 probe disconnected (Supply temperature)

AL03

Alarm B3 probe disconnected (Discharge temperature compressor 1)

AL05

Alarm B5 probe disconnected (Return humidity)

AL06

Alarm B6 probe disconnected ( Return humidity )

AL07

Alarm B7 probe disconnected (Outdoor humidity)

AL08

Alarm B8 probe disconnected (Water inlet temperature circuit 2)

AL09

Alarm B9 probe disconnected (Water outlet temperature circuit 3)

AL11

Alarm B11 probe disconnected (Low pressure C1, 2 circuits units only)

AL12

Alarm B12 probe disconnected (Low pressure C2, 2 circuits units only )

ALb1

Alarm B1 probe disconnected (Outdoor temperature )

ALb2

Alarm B2 probe disconnected (Supply temperature )

ALb3

Alarm B3 probe disconnected (Discharge temperature compressor 1)

ALb5

Alarm B5 probe disconnected (Return humidity )

ALb6

Alarm B6 probe disconnected (Return humidity )

ALb7

Alarm B7 probe disconnected (Outdoor humidity )

ALb8

Alarm B8 probe disconnected (Water inlet temperature circuit 2)

ALb9

Alarm B9 probe disconnected (Water outlet temperature circuit 3)

ALF6

Alarm thermal compressor

ALF7

Alarm thermal indoor fan

ALH1

Alarm antifrost 1 (Inlet water below 12ºC)

ALH2

Alarm antifrost 2 (Outlet water below 6ºC)

ALH3

Alarm antifrost 3 (Inlet water < 15ºC and

ΔT > 8ºC)

ALH4

Alarm antifrost 4 (Compressor ON and

ΔT Inlet/Outlet water lower 1.5ºC)

ALIF

Alarm flow switch

ALPA

Alarm high pressure switch circuit 1

ALPB

Alarm low pressure switch circuit 1

ALPM

Alarm min. pressure switch

ALRF

Alarm refrigerant too low

A2F7

Alarm thermal compressor 2 (2 circuits units)

A2F8

Alarm thermal indoor fan 2 (2 circuits units )

A2PA

Alarm high pressure switch circuit 2

A2PB

Alarm low pressure switch circuit 2

A2PM

Alarm min. pressure switch circuit 2

A2RF

Alarm refrigerant too low circuit 2

Summary of Contents for CCHBA/CCHA 1201




































Search results

Summary of Contents for CCHBA/CCHA 1201

Reviews:

Related manuals for CCHBA/CCHA 1201

Brands by name

Popular brands

Hitecsa CCHBA/CCHA 1201, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for CCHBA/CCHA 1201

Reviews:

Related manuals for CCHBA/CCHA 1201

Brands by name

Popular brands