Note
Note
When you try to have Link, please located TX & RX less than a 3 feet distance.
Receiver Connection Diagrams (AXION2)
Electric powered car with Electronic Speed Control
Use this method on electric car using ESC’s
providing power to the receiver and servo functions.
How to Link (ID-Set)
When you purchase a radio set that Transmitter and receiver include together in the box, each device
are linked already from the factory.
If you purchase extra receivers or transmitter, you need to have Link with current your device together.
How to Link LYNX 4S with AXION receivers
1. Surface AFHSS 2.4GHz Transmitter (LYNX 4S)
(1) Select [RX-BIND] from LYNX 4S system menu
(2)Select receiver type from menu
(3) Run Bind Mode
(4) When Blue LED on receiver is solid on, Link is complete.
(5) Turn off the Bind Mode pressing ESC button twice
(6) Turn off the receiver and Turn on again.
2. AXION Series Receiver
(1) Run Bind Mode in Transmitter.
(2) Press and hole the LINK button and turn on the receiver.
(3) release button, and then LED will be blink Blue and Red rapidly..
(4) When LED turn on Solid Bleu, Link set up is complete
Fail-safe or Hold Mode Switch
If you use the FAIL-SAFE function, and set it up properly, should the receiver signal somehow be
interrupted or interference were to occurred, the servos will move to your pre-set FAIL-SAFE position
you previously stored in the receiver during the FAIL-SAFE set-up.
If FAIL-SAFE has not been activated, the signal is switched off after the HOLD period of 1 sec. This
means that the servos become “soft” and remain in their last commanded position under no load
(this may equate to full-throttle!), until a valid signal is picked up again.
In the interests of safety, we recommend that FAIL-SAFE should always be activated, and the FAIL-SAFE
settings should be selected so as to bring the model to a non-critical situation (e.g. motor idle / electric
motor OFF, control surfaces neutral, or full brake, etc.)
HHR
Power Battery
Motor
BEC
ESC
SERVO
Steering
AMB
AMB
SERVO
SERVO
SERVO
Steering
Engine
AUX
SERVO
AUX
Receiver
Battery
Fail Safe- / Hold Set up (AXION 2&4)
Receiver Connection Diagrams (AXION4)
Glow, gas or electric powered car using a separate
receiver battery supply.
Follow this connection diagram when using a regulated
2cell Li-Po/Li-Fe, or 4.8~7.2V (4~6cell) NiMh/NiCd.
Receiver battery,
Turn on Transmitter and receivers..
Select [FAIL SAFE] from transmitter menu,
and then you can select Fail safe or Hold.
After you set, please press ‘SEND’ button
Fail safe and Hold function of AXION Receivers
can be set by Lynx 4S transmitter.
When you press ‘SEND’ on transmitter, LED on receivers will be blink in ‘BLUE’ rapidly.
If LED turn on solid Blue, set up is completed.
Set up the fail safe position of trigger/ steering wheel/ switch before you set up
(ie. Full brake, engine idle),
Make sure to check Fail Safe set properly, turn off the transmitter and check the position.
After 1sec, if there is no signal, Fail Safe function will be activated.
Please check Fail Safe position every time before you run
The FAIL-SAFE settings should be checked every time before you run the engine/motor.
This product is designed to be used as a R/C hobby product and should be operated under
local regulation.
Hitec Service
12115 Paine St. Poway CA 92064
1-858-748-6948
E-mail: [email protected]
Hitec RCD Korea, Inc.
(43, Yangcheong 3-gil, Ochang-eup, Cheongwon-Gu, Cheongju-si, Chungcheongbuk-do, Korea) / www.hitecrcd.com / Made in the Philippines
