manualshive.com logo in svg

Hitachi WH14DBL, Technical Data And Service Manual

Share
Download
Hitachi WH14DBL Technical Data And Service Manual Download Page 19

-16-

battery, please charge the next battery after about a fifteen-minute interval.

(8) The charger case is equipped with air vents to protect the internal electronic components from

overheating. Caution the customers not to allow foreign materials such as metallic or

flammable objects to be dropped or inserted into the air vents. This could cause electric shock,

fire or other serious hazards.

(9) Do not attempt to disassemble the storage battery or the charger.

Special devices, such as a thermostat, are built into the storage battery and charger to permit

rapid charging. Incorrect parts replacement and/or wiring will cause malfunctions which could

result in fire or other hazards. Instruct the customers to bring the Model WH 14DBL to an

authorized service center in the event repair or replacement is necessary.

(10) Disposal of the storage battery

Ensure that all customers understand that the storage battery should be returned to the

Hitachi power tool sales outlet or authorized service center when it is no longer capable of

being recharged or repaired. If thrown into a fire, the battery may explode, or if discarded

indiscriminately, leakage of the cadmium compound contained in the battery may cause

environmental pollution.

(11) Effect of the permanent magnet

The Model WH 14DBL has a strong permanent magnet in its motor. Please instruct the

customers about adhesion of dust to the Model WH 14DBL and effect on electronic devices as

follows.

• Do not place the Model WH 14DBL on a workbench or workplace where metal dust is

scattered about.

• Do not touch the dust-adhered Model WH 14DBL. Instruct the customers to remove adhered

dust with a brush.

• Users of medical electronics such as a pacemaker must not use or get close to the Model

WH 14DBL.

• Do not bring precision equipment such as a mobile-phone or electronic recording media such

as a magnetic card close to the Model WH 14DBL.

(12) Keep the battery out of dust.

• Protect the battery from being covered with dust during operation.

• Protect the battery from being covered with dust accumulated on the Model WH 14DBL

during operation.

• Do not leave the battery in a dusty area when not in use.

• Remove dust from the battery and store it separating from metallic parts such as screws and

nails.

Summary of Contents for WH14DBL










































Reviews:

No comments

Brands by name

Popular brands

Load more brands