background image

-1-

MN1-5053 Rev. 15

1. Safety Precautions

1-1. Intended use

This probe is intended for use by a doctor when placed to direct contact with human internal organs during 

surgery making ultrasonic observations.

With the exception of Japan, you can use the probe in neurosurgery applications if you attach our recommended 

transducer cover to the probe.  When using the probe in neurosurgery applications, refer to Section 1-2-2 under 

“Precautions when using the probe in neurosurgery applications”.

 Caution

Do not use this equipment for other than its intended purpose.

Use for other purposes can cause burns or other injuries to the patient or operator.

1-2. Usage precautions

The terms below are used in the safety information provided to prevent hazards and injuries to the operator 

or patients. The severities of the hazard and injury that can occur when failing to observe the displayed 

safety information are indicated in four levels: "Danger", "Warning", "Caution" and "Note".

 Danger

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to 

the operator or patient.

 Warning

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to 

the operator or patient.

 Caution

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury 

to the operator or patient or property damage only.

 Note

Indicates a strong request concerning an item that must be observed in order to prevent damage or 

deterioration of the equipment and also to ensure that it is used efficiently.

The type of safety information is indicated by the symbols below.

This symbol means attention is required.

This symbol means that the described action is prohibited.

This symbol means the described action is mandatory.

Summary of Contents for UST-547























































Reviews: