background image

2.2  IMPORTANT NOTICE

The supplementary information about the purchased products 
is supplied in a CD-ROM, which can be found bundled with the 
outdoor unit. In case that the CD-ROM is missing or it is not 
readable, please contact your HITACHI dealer or distributor.
PLEASE READ THE MANUAL AND THE FILES ON THE 
CD-ROM CAREFULLY BEFORE STARTING WORK ON THE 
INSTALLATION OF THE AIR CONDITIONING SYSTEM. Failure 
to observe the instructions for installation, use and operation 
described in this documentation may result in operating failure 
including potentially serious faults, or even the destruction of the 
air conditioning system.
This manual should be considered as a permanent part of the 

air conditioner. This manual gives a common description and 
information for this air conditioner which you operate as well as 
for other models.

Refer to the models codification to confirm the main 

characteristics of your system.
Verify, in accordance with the manuals which appear in the 

outdoor and indoor units, that all the information required for the 

correct installation of the system is included and correspond to 
your air conditioner model. If this is not the case, contact your 
distributor.

If you have any questions, contact your service contractor of 

HITACHI.

2.3  ADDITIONAL INFORMATION ABOUT SAFETY

!

D A N G E R

•  HITACHI is not able to foresee all the circumstances which may 

result in a potential danger.

•  Do not pour water into the indoor or outdoor unit. These products 

are equipped with electrical parts. If water contacts with electrical 

components then it will cause a serious electrical shock.

•  Do not handle or adjust the safety devices inside the indoor and 

outdoor units. The handling or adjustment of these devices may 

result in serious accident.

•  Do not open the service cover or access the indoor or outdoor 

units without disconnecting the main power supply.

•  In case of fire Turn OFF the main switch, put out the fire at once 

and contact your service contractor.

•  This  air  conditioner  is  equipped  with  a  high  pressure  vessel 

under  PED  (Pressure  Equipment  Directive).  The  pressure 

vessel  has  been  designed  and  tested  before  shipment 

according  to  PED.  Also,  in  order  to  prevent  the  system  from 

an  abnormal  pressure,  a  high  pressure  switch,  which  needs 

no  field  adjustment,  is  utilized  in  the  refrigeration  system. 

Therefore,  this  air  conditioner  is  protected  from  abnormal 

pressures. However, if abnormally high pressure is applied to 

the  refrigeration  cycle  including  the  high  pressure  vessel(s), 

it  will  result  in  serious  injury  or  death  due  to  explosion  of 

the  pressure  vessel.  Do  not  apply  a  pressure  higher  than  the 

following pressure to the system, by modifying or changing the 

high pressure switch.

•  Do not handle, modify or change the high pressure switch in the 

air conditioning unit. If abnormally high pressure is applied to the 

elements in the air conditioning unit refrigerant cycle, including 

the  high  pressure  vessels,  these  could  explode  resulting  in 

serious injury or loss of life.

Location

Structure

Accumulator

Compressor

High pressure switch

Contact point 

Pressure detected

Connected to the electrical wire

The label for the vessel under PED 

are attached on the high pressure 

vessel. The pressure vessel capacity 

and vessel category are indicated on 

the vessel.

The high pressure switch is indicated 

on the electrical wiring diagram in the 

outdoor unit as HPS connected to printed 

circuit board (PCB) in the outdoor unit.

Start-up and Operation: 

Check to ensure that all the stop 

valves are fully opened and no obstacle exists at the inlet/outlet 
sides before start-up and during the operation.

Maintenance:

 Periodically check the high pressure side 

pressure. If the pressure is higher than the maximum allowable 
pressure, stop the system and clean the heat exchanger or 
remove the cause.

Refrigerant

Maximun allowable 

pressure (MPa)

High pressure switch 

cut-out value (MPa)

R410A

4.15

4.00 ~ 4.10

!

C A U T I O N

•  Check for refrigerant leakage in detail. It may hinder respiration as the 

gas displaces the air in the room. Also harmful gases would occur if a 

fire were being used in the room.

•  Fit the indoor unit, the outdoor unit, the remote control and the cable 

at a minimum of 3 meters away from sources where electromagnetic 

waves radiate directly towards the electrical box and the components 

of the unit, such as medical equipment. Electronic noise may result in 

the incorrect operation of the unit.

•  Do not use sprays, such as insecticides, varnishes or enamels or any 

other inflammable gas within a meter of the system.

•  If the circuit breaker or supply fuse of the unit comes on frequently, 

stop the system and contact the service suppler.

•  Do not place any foreign material (branches, sticks, etc.) in the air 

inlet or outlet of the unit. These units are fitted with high speed fans 

and contact with any object is dangerous.

•  This  appliance  must  be  used  only  by  adult  and  capable  people, 

having  received  the  technical  information  or  instructions  to  handle 

this appliance properly and safely.

•  The  air  conditioning  system  should  only  be  installed,  carry  out 

maintenance or inspection by qualified personnel, with the necessary 

resources,  tools  and  equipment,  who  are  familiar  with  the  safety 

procedures required to successfully carry out the installation.

•  Children should be supervised to ensure that they do not play with 

the appliance.

•  This air conditioner has been designed for standard air conditioning 

for human beings. For use in other applications, please contact your 

HITACHI dealer or service contractor.

?

N O T E

•  The air in the room should be renewed and the room ventilated every 

3 or 4 hours.

•  The  system  fitter  and  specialist  shall  provide  anti-leak  safety  in 

accordance with local regulations.

SAFETY

PMML0511 rev.1 - 06/2019

20

Summary of Contents for RAS-4-6FSVNME









































Reviews: