manualshive.com logo in svg

Hitachi RAM-68NP3B, Service Manual, Page: 71 / 79

Share
Download
Hitachi RAM-68NP3B Service Manual Download Page 71

LD351

 

11 times blink

Fan stop due to strong wind

LD401, LD402 or LD403 blink

Communication error between 

indoor and outdoor

LD401:  Indoor No.1
LD402:  Indoor No.2

Once stop when wind is in heavy condition.

It will resume back when wind become normal.

Please confirm the connecting cable between indoor

and outdoor. (Is connector connected properly?)

Are F8~F10 (5A fuses) blown?

The wind is heavy? Confirm

the unit is restarting. (Takes 

about few minutes to restart)

Outdoor electrical and outdoor fan 

motor is OK.

After unit 

is restart

Stop

Check outdoor fan motor. Detail shall 

refer to outdoor fan motor page or refer to

label on the electrical cover.

Any abnormality found at the fan motor?

Fan motor

Abnormal

Please replace outdoor fan motor.

Connecting cable repair and 

replace the fuse.

Is the indoor unit timer lamp show 

12 times blinking?

Recheck indoor unit.

Repair the connecting cable.

Fan motor is normal

Please replace Inverter PWB.

(Outdoor fan driven circuit abnormal)

Yes

Yes

Abnormal

Abnormal

No

Normal

Abnormal

Normal

Please replace Main PWB.

Normal

LD403:  Indoor No.3

Summary of Contents for RAM-68NP3B
















































































Reviews:

No comments