Hitachi RAD-25NH4 Installation Manual Download Page 9

– 9 –

ENGLISH

DEUTSCH

FRANÇAIS

IT

ALIANO

SP

ANISH

POR

TUGUÊS

∂ÏÏËÓÈο

Р

УССКИЙ

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C.
When it is under 15°C, the dehumidifying function will not work.

When you want to change the operation mode, please use the FUNCTION
selector.

Set the desired temperature is available.

You also can use the FUNCTION selector to select this operation.

Press the FUNCTION selector so that the display indicates

(DEHUMIDIFY).

The FAN SPEED is set at LOW automatically.
The FAN SPEED button does not work.

Press the 

(START/STOP) button.

1

START

STOP

• Dehumidifying takes place with a target temperature which is slightly lower than the room temperature

setting. (However, target temperature is 16°C for a temperature setting of 16°C.)
If the room temperature becomes lower than the target value, operation stops. If the room temperature
becomes higher than the target value, operation restarts.

• The preset room temperature may not be reached depending on the number of people present in the room

or other room conditions.

Dehumidifying Function

Summary of Contents for RAD-25NH4





















Reviews: