Hitachi RAC-70WPA Manual Download Page 11

–  11  –

EN

G

L

ISH

2.      Washable  Front  Panel

Removing  the  Front  Panel

Attaching  the  Front  Panel

!

CAUTION

 

Do not splash or direct water to the body of the unit when cleaning it as 
this may cause short circuit.

 

Never use hot water (above 40°C), benzine, gasoline, acid, thinner or a 
brush, because they will damage the plastic surface and the coating.

 

Remove the front panel and wash with clean water.
Wash it with a soft sponge.
After  using  neutral  detergent,  wash  thoroughly  with 
clean water.

 

When front panel is not removed, wipe it with a soft 
dry cloth. Wipe the remote controller thoroughly with 
a soft dry cloth.

 

Wipe the water thoroughly.
If  water  remains  at  indicators  or  signal  receiver  of 
indoor unit, it causes trouble.

Method of removing the front panel.
Be  sure  to  hold  the  front  panel  with  both  hands  to 
detach and attach it.

 

When  the  front  panel  is  fully  opened  with 
both  hands,  push  the  right  arm  to  the  inside 
to release it, and while closing the front panel 
slightly, put it out forward.

 

Move the projections of the left and right arms 
into the Flanges in the unit and securely insert 
them into the holes.

Arm

Hole

Projection

Flanges

Summary of Contents for RAC-70WPA















Reviews: