Hitachi L32VK06U Instructions For Use Manual Download Page 11

English

- 6 -

by pulling from the power cord and never touch the 
power cord with wet hands as this could cause a short 
circuit or electric shock. Never make a knot in the cord 
or tie it with other cords. The power cords should be 
placed in such a way that they are not likely to be 
stepped on. A damaged power cord can cause fi re or 
give you an electric shock. When it is damaged and 
needs to be replaced, it should be done by qualifi ed 
personnel.

This TV receiver is supplied with a moulded mains 
plug. The mains plug must not be cut off, as it may 
contain a special radio interference fi lter, the removal 
of which could lead to impaired performance. If you 
wish to extend the lead, obtain an appropriate safety 
approved extension lead or consult your dealer. 

Observe the manufacturers instructions when 
connecting extension leads to the set. Check the fuse 
rating on the new plug; this should be fi tted with a 5 
Amp fuse which conforms to either ASTA or BSI 
(BS1362) approvals, these are easily identifi able by 

either the 

ASA

or

 symbols. If you are in any doubt 

about the installation of an extension lead, please 
consult a competent electrician.

Moisture and Water 

Do not use this device in a humid and 
damp place (avoid the bathroom, the 
sink in the kitchen, and near the washing 
machine). Do not expose this device to 
rain or water, as this may be dangerous 
and do not place objects fi lled with liquids, 
such as fl ower vases, on top. Avoid from 
dripping or splashing.

If any solid object or liquid falls into the cabinet, unplug 
the TV and have it checked by qualifi ed personnel 
before operating it any further.  

Cleaning

Before cleaning, unplug the TV set 
from the wall outlet. Do not use liquid or 
aerosol cleaners. Use soft and dry cloth. 

Ventilation 

The slots and openings on the TV set are intended for 
ventilation and to ensure reliable operation. To prevent 
overheating, these openings must not be blocked or 
covered in anyway. 

Heat and Flames 

The set should not be placed near to open 
fl ames and sources of intense heat such 
as an electric heater. Ensure that no open 
fl ame sources, such as lighted candles, 
are placed on top of the TV. Batteries 
should not be exposed to excessive heat 
such as sunshine, fi re or the like. 

Lightning

In case of storm and lightning or when 
going on holiday, disconnect the power 
cord from the wall outlet.

Replacement Parts 

When replacement parts are required, make sure that 
the service technician has used replacement parts, 
which are specifi ed by the manufacturer or have the 
same specifi cations as the original one. Unauthorized 
substitutions may result in fi re, electrical shock or 
other hazards.

Servicing

Please refer all servicing to qualified 
personnel. Do not remove the cover 
yourself as this may result in an electric 
shock.

Waste Disposal 

Instructions for waste disposal:

• Packaging and packaging aids are recyclable and 

should principally be recycled. Packaging materials, 
such as foil bag, must be kept away from children.

• Batteries, including those which are heavy metal-

free, should not be disposed of with household 
waste. Please dispose of used battery in an 
environment friendly manner. Find out about the 
legal regulations which apply in your area. Don’t try 
to recharge batteries. Danger of explosion. Replace 
batteries only with the same or equivalent type. 

• Cold cathode fluorescent lamp in LCD PANEL 

contains a small amount of mercury; please follow 
the local laws or regulations for disposal. 

Information for Users  in European 
Union Countries

The above mark is in compliance with 
the Waste Electrical and Electronic 
E q u i p m e n t   D i r e c t i v e   2 0 0 2 / 9 6 /
EC (WEEE). The mark indicates 
the requirement NOT to dispose 
the equipment including any spent 
or discarded batteries as unsorted 
municipal waste, but use the return 
and collection systems available. If the batteries or 
accumulators included with this equipment display 
the chemical symbol Hg, Cd, or Pb, then it means that 
the battery has a heavy metal content of more than 
0.0005% Mercury, or more than 0.002% Cadmium or 
more than, 0.004% Lead.

Disconnecting the Device 

The mains plug is used to disconnect TV set from 
the mains and therefore it must remain readily 
operable.

Summary of Contents for L32VK06U











































Reviews: