background image

5.4  VALGFRIE FUNKTIONER

Some optional functions of the indoor units have been added so that they can be managed from the BMS.

Offset

Beskrivelse

Værdier

Læs/Skriv

0

b1 (Heating temperature compensation)

0~4

Læs/Skriv

1

b2 (Circulation function at heating Thermo-OFF)

0~1

Læs/Skriv

2

b4 (Change of filter cleaning period)

0~4

Læs/Skriv

3

c5 (Static pressure selection)

0~2

Læs/Skriv

4

c8 (Control by the temperature sensor of the remote control switch)

0~2

Læs/Skriv

5

Cb (Selection of forced stoppage logic)

0~1

Læs/Skriv

6

Cd (Stop of indoor unit fan during cooling Thermo-OFF conditions)

0~1

Læs/Skriv

7

CE (Stop of indoor unit fan during heating Thermo-OFF conditions)

0~1

Læs/Skriv

8

d1 (Management of indoor unit operation after a power supply cut off -option 1)

0~1

Læs/Skriv

9

d3 (Management of indoor unit operation after a power supply cut off -option 2)

0~1

Læs/Skriv

10

d4 (RPI(M) Prevention of low air outlet temperature in cooling mode)

0~1

Læs/Skriv

11

d5 (Prevention of low air outlet temperature in heating mode)

0~1

Læs/Skriv

12

E1 (KPI: Ventilation mode / Econofresh cooling mode)

0~2

Læs/Skriv

13

E2 (KPI: Increase of air supply volume / Econofresh enthalpy Sensor)

0~1

Læs/Skriv

14

E4 (KPI: Pre-cooling / preheating period / Econofresh: CO2 sensor)

0~2

Læs/Skriv

15

E8 (Control for stop of the indoor unit fan during heating Thermo-OFF conditions 

(with remote sensor THM-R2AE connected to the THM4 connector in the indoor 

unit PCB)

0~1

Læs/Skriv

16

E9 (Intermittent fan operation in heating stop)

0~1

Læs/Skriv

17

Eb (Indoor unit fan control during cooling Thermo-OFF conditions)

0~2

Læs/Skriv

18

EE (Control in “Automatic” indoor fan speed mode)

0~1

Læs/Skriv

19

EF (Control in “Automatic” indoor fan speed mode (supporting High H))

0~1

Læs/Skriv

20

H4 (KPI: Operation modes for the ventilation unit with energy recovery)

0~1

Læs/Skriv

21

K5 (Detection level of the motion sensor kit)

0~2

Læs/Skriv

22

K6 (Selection of allowed operation modes when the control sensor of the indoor unit 

is set by C8 function)

0~3

Læs/Skriv

?

N O T E

•  Register address is calculated as: 40000+(Modbus_Id*100)+offset
•  Modbus_Id as configured by configuration software

5.5  LISTE MED ALARMKODER

Adresse 19 angiver alarmkode som vist i indendørsenhed. Se servicevejledningen for forklaring af alarmer og reparationsprocedure 
i tilfælde af alarm på enten indendørsenhed eller udendørsenhed.

5.6  FEJLFINDING

ALARMKODE

BESKRIVELSE

MODFORANSTALTNINGER

LED2 blinker

Unormal drift

Afbryd strømforsyningen til enheden og gentilslut den efter 5 sek. Hvis LED2 stadig blinker 

bedes du kontakte Hitachi kundeservice. 

DANSK

DRIFT

PMML0351A rev.4 - 04/2020

151

Summary of Contents for HC-A16MB



















































Reviews: