English
8
c)
When
battery
pack
is
not
in
use,
keep
it
away
from
other
metal
objects
like
paper
clips,
coins,
keys,
nails,
screws,
or
other
small
metal
objects
that
can
make
a
connection
from
one
terminal
to
another.
Shorting the battery terminals together may cause
burns or a
fi
re.
d)
Under
abusive
conditions,
liquid
may
be
ejected
from
the
battery;
avoid
contact.
If
contact
accidentally
occurs,
fl
ush
with
water.
If
liquid
contacts
eyes,
additionally
seek
medical
help.
Liquid ejected from the battery may cause irritation or
burns.
6)
Service
a)
Have
your
power
tool
serviced
by
a
quali
fi
ed
repair
person
using
only
identical
replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep
children
and
in
fi
rm
persons
away.
When
not
in
use,
tools
should
be
stored
out
of
reach
of
children
and
in
fi
rm
persons.
CORDLESS
IMPACT
DRIVER
DRILL
SAFETY
WARNINGS
1.
Wear
ear
protectors
when
impact
drilling.
Exposure to noise can cause hearing loss.
2.
Use
auxiliary
handle(s),
if
supplied
with
the
tool.
Loss of control can cause personal injury.
3.
Hold
power
tool
by
insulated
gripping
surfaces,
when
performing
an
operation
where
the
cutting
accessory
or
fastener
may
contact
hidden
wiring.
Cutting accessory or fasteners contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
4. Always charge the battery at a temperature of 0°C –
40°C. A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature higher than 40°C.
The most suitable temperature for charging is that of
20°C – 25°C.
5. When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
Do not charge more than two batteries consecutively.
6. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
7. Never disassemble the rechargeable battery and
charger.
8. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric current
and overheat. It results in burn or damage to the battery.
9. Do not dispose of the battery in
fi
re.
If the battery is burnt, it may explode.
10. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
11. Using an exhausted battery will damage the charger.
12. Do not insert object into the air ventilation slots of the
charger.
Inserting metal objects or in
fl
ammables into the charger
air ventilation slots will result in electrical shock hazard or
damaged charger.
13. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
14. This product contains a strong permanent magnet in the
motor.
Observe the following precautions regarding adhering of
chips to the tool and the e
ff
ect of the permanent magnet
on electronic devices.
CAUTION
○
Do
not
place
the
tool
on
a
workbench
or
work
area
where
metal
chips
are
present.
The chips may adhere to the tool, resulting in injury or
malfunction.
○
If
chips
have
adhered
to
the
tool,
do
not
touch
it.
Remove
the
chips
with
a
brush.
Failure to do so may result in injury.
○
If
you
use
a
pacemaker
or
other
electronic
medical
device,
do
not
operate
or
approach
the
tool.
Operation of the electronic device may be a
ff
ected.
○
Do
not
use
the
tool
in
the
vicinity
of
precision
devices
such
as
cell
phones,
magnetic
cards
or
electronic
memory
media.
Doing so may lead to misoperation, malfunction or loss of
data.
CAUTION
ON
LITHIUM
-
ION
BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand, please
be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○
During work make sure that swarf and dust do not fall on
the battery.
○
Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
○
Do not store an unused battery in a location exposed to
swarf and dust.
○
Before storing a battery, remove any swarf and dust that
may adhere to it and do not store it together with metal
parts (screws, nails, etc.).
00Book̲DV14DJL̲WE.indb 8
00Book̲DV14DJL̲WE.indb 8
2014/03/10 12:43:51
2014/03/10 12:43:51
