manualshive.com logo in svg

Hitachi DKC910I, Installation Manual

Share
Download
Hitachi DKC910I Installation Manual Download Page 84

Copyright © 2019, 2021, Hitachi, Ltd.

DKC910I

Hitachi Proprietary

[INST(RM)08-01-100]

Rev.0.1

INST(RM)08-01-100

(i)  <Start of the remove>

Click [Yes] in response to the message 

“

The SVP and SSVP will be removed. Do you want to 

continue?

”

The REP LED (red) on the Additional SSVP lights up. (see 

Figure 8-7

)

(j) 

<The Additional SVP power off>

“

Turn off the power supply of the SVP. After the operation has completed, select [OK].

”

 is 

displayed.

(k) 

<Powering off the Additional SVP>
Press the SVP PS ON/OFF switch on the Additional SVP for about one second to power off the 

Additional SVP.

Check that the SVP POWER LED on the front of the Additional SVP goes off (see 

Figure 8-4

).

NOTE:  If the SVP POWER LED does not go off after about three minutes have passed, press 

the SVP PS ON/OFF switch for five seconds or more (forced power-off), and then 
check that the SVP POWER LED goes off.

NOTE:  If the Additional SVP is powered off, the REP LED (red) on the Additional SSVP 

goes off (see 

Figure 8-7

).

Click [OK] in response to the message in 

Step (j)

.

Summary of Contents for DKC910I











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands