Hitachi DKC910I Installation Manual Download Page 64

Page: 64 / 138

DKC910I

Hitachi Proprietary

[INST(RM)06-01-10]

Rev.2

INST(RM)06-01-10

6. Removing Disk Board (DKB)

Be sure to read the notice shown below before performing the following procedure.

NOTICE:

Before removing Disk Boards (DKBs), check that Drive Boxes are already removed.

If Drive Boxes are not yet removed, remove them by following the procedure in

“

Removing Drive Boxes

”

1. Connecting the Maintenance PC

Connect the Maintenance PC to the SSVP, and then log in to the SVP.
•

“

Attachment/Removal Procedure of Maintenance PC

”

(INST(IN)13-02-10)

•

“

Connection to the SVP

”

(SVP01-30)

2. Starting the SVP window

From the menu of Web Console, click [Maintenance Components] - [Maintenance Other Components].

3. Changing the operation mode

Change the mode to [View Mode].

4. Starting Maintenance Utility

In the SVP window, click [Maintenance Utility] (See

“

Starting Maintenance Utility

”

(MU01-10)

.).

Summary of Contents for DKC910I










































































































































Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands

Hitachi DKC910I, Installation Manual

Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands