Hitachi DKC910I Installation Manual Download Page 27

Page: 27 / 138

DKC910I

Hitachi Proprietary

[INST(RM)04-01-10]

Rev.2

INST(RM)04-01-10

4. Removing Drive Boxes

Do this work after conﬁrming the notices shown below.

NOTICE:

Check that no Drives are installed in Drive Boxes to be installed. If Drives are

installed, see

4.1 Estimated Work Time

The estimated working hours for removing Drive Boxes are the total of the following A, B, C, and D.

Table 4-1 Estimated Working Hours for Removing Drive Boxes

Removal type

Process

Estimated work time

Remarks

A Chassis

Chassis removal time

SBX/UBX/FBX/NBX: 60 min

Micro-program processing
time (path)

20 sec

(number of existing c number of

chassis to be removed)

(*1)

HDD

HDD removal time

1 min / 1 HDD

Micro-program processing

time (HDD) (*2)

• In case of SBX, UBX, FBX:

30 seconds/Drive Box

• In case of NBX

20 seconds/Drive Box

*1: The number of paths of each model is as shown below.

DKC: Four paths or eight paths (when one Disk Board option (eight paths) is used.)

*2: The micro-program processing time (HDD) is the time taken for

Checking the Drive Removal by Maintenance Utility

”

Summary of Contents for DKC910I










































































































































Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands

Hitachi DKC910I, Installation Manual

Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands