Hitachi DKC910I Installation Manual Download Page 8

Page: 8 / 138

DKC910I

Hitachi Proprietary

[INST(RM)03-01-10]

Rev.1

INST(RM)03-01-10

3. Removing Drives

Decide drive position to be removed referring to

“

Relational Drive position with Parity Group

”

(INST(AD)01-02-10)

NOTE : • When removing the Drives included in the parity group, it is necessary to delete the

parity group in advance. Refer to

“

Deleting Parity Group

”

(WEBCON03-450)

• When removing the Drives allocated to the Spare Drive, it is necessary to

delete the Spare Drive in advance. Refer to

“

Allocating/Deleting Spare Drives

”

(WEBCON03-390)

3.1 Before Removing Drives

1. Connecting the Maintenance PC

Connect the Maintenance PC to the SSVP, and then log in to the SVP.
•

“

Attachment/Removal Procedure of Maintenance PC

”

(INST(IN)13-02-10)

•

“

Connection to the SVP

”

(SVP01-30)

2. Starting the SVP window

From the menu of Web Console, click [Maintenance Components] - [Maintenance Other Components].

3. Changing the operation mode

Change the mode to [View Mode].

4. Starting Maintenance Utility

In the SVP window, click [Maintenance Utility] (See

“

Starting Maintenance Utility

”

(MU01-10)

.).

Summary of Contents for DKC910I










































































































































Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands

Hitachi DKC910I, Installation Manual

Search results

Summary of Contents for DKC910I

Reviews:

Brands by name

Popular brands