6
CP-X995W
7
CP-X995W
4. Adjustment
4-1 Before adjusting
4-1-1 Adjustment menu
1. Before starting adjustment, warm up the projector
for about 10 minutes. (Blank white)
2. Set Zoom Wide to Max. and project an image a
distance of more than 40 inches.
3. Normalizing the video adjustment.
(Press the [MENU] button of the Remote control
transmitter to display the Setup menu, then press
the [RESET] button. And select the [DEFAULT].)
*note : The setup menu is not displayed on with no
signal.
4. Perform all adjustments from the Adjustment menu.
Perform the following operations to display the
Adjustment menu.
a. Press the [MENU] button of the Remote control
transmitter (the Setup menu will appear).
b. Next, press the [RESET] button one time. And
press the [RESET] button again for 5 seconds
or more (the Adjustment menu will appear).
4-2 Ghost adjustment
Signals for internal adjustment
���
���
�������
�����
Adjustment procedure
1. Use DAC-P - GHOST - R: in the Adjustment menu
to adjust so that R color ghost is at a minimum.
(Press the [RESET] button, then raise the value.
When a ghost appears to the left of a vertical line,
reduce the value by 2 steps.)
2. In the same way, use DAC-P - GHOST-G: in the
Adjustment menu to adjust so that G color ghost is
at a minimum.
3. In the same way, use DAC-P - GHOST-B: in the
Adjustment menu to adjust so that B color ghost is
at a minimum.
4-1-2 Required adjustment
Relation between the replacement part and required
adjustment are shown in Table 4-1-2.
Tabel 4-1-2: Required adjustment
��������
����������
��������
�����������
��������
������
��������
����
��������
�����
����
����
�����
����������
�������
����������
����
����������
�������������
����������
����������������
����������
�������������
: need
: recommend : no need
Summary of Contents for CP-X995W
