background image

ENGLISH-9

ENGLISH

ENGLISH-9

OPERATIONS

Switching the Power Supply ON/OFF

Switching Power ON

1. Check that the power cord is connected correctly.
2. Set the power switch to [ | ]. The standby mode is selected, and the Power indicator is turned to

orange.

3. Press the STANDBY/ON 

button on the control panel or the remote control transmitter.

Warm-up begins and the Power indicator blinks in green.

4. The Power indicator ceases blinking and turns to green when power is on. Open the slide lens

door.

5. Adjust picture size using the projection lens Zoom Knob.
6. Adjust focus using the projection lens Focus Ring.

Switching Power OFF

1. Press the STANDBY/ON button on the control panel or the remote control transmitter for

approximately two second. The projector lamp is extinguished and lamp cooling begins. The
Power indicator blinks orange during lamp cooling. Pressing the STANDBY/ON 

button has

no effect while the Power indicator is blinking.

2. The system assumes the Standby mode when cooling is complete, and the Power indicator ceases

blinking and changes to orange. Check that the indicator is orange and set the Power switch to
[

O

].

3. The Power indicator is extinguished when power is off. Do not forget to close the lens door.

WARNING

Please read this manual, and the separate “SAFETY INSTRUCTIONS” thoroughly before
using the equipment. Always ensure that the equipment is used safely.

Power Switch

Slide Lens Door

STANDBY/ON Button

POWER Indicator

STANDBY/ON

LASER

VIDEO

BLANK

RGB

AUTO

MENU

MENU SELECT

POSITION

RESET

FREEZE

MAGNIFY

OFF

VOLUME

MUTE

STANDBY/

ON Button

Zoom Knob

Focus Ring

NOTE:

• Except in emergencies, do not turn off unless the Power indicator is orange as it will reduce the

life of the projector lamp.

• To prevent any troble, turn on/off the projector when the computer or video tape recorder is OFF.

Providing a RS-232C cable is connected, turn on the computer before the projector.

Summary of Contents for CP-X320

























Reviews: