Hitachi CM2096ME User Manual Download Page 9

q

Use only the correct voltage power outlet with safety ground connection.

110   120 V for USA, Canada, etc.

200   240 V for Europe. etc.

(This monitor automatically selects the input voltage 110   1201200   240V.)

The receptacle should be close to the monitor and easily accessible.

 

 

   

THIS PRODUCT IS SUPPLIED WITH A TWO 

 PLUG FOR USE IN MAINLAND

EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE.

NOTE:
ELECTRICAL CONNECTION
Your monitor requires an electrical supply of 240 volts   50 hertz and should be protected
by a 5 amp fuse. Your equipment is supplied with a plug incorporating a 5 amp fuse fitted

to the mains lead. If the plug that is fitted to the equipment is not suitable for your socket

outlet, it must be cut off and an appropriate plug must be fitted. The cut off plug should
be disposed of, do not insert it into a 13 amp socket to prevent the hazard of electric

shocks. With plugs not incorporating a fuse, the circuit must be protected by 5 amp fuse.

WARNING: THIS EQUIPMENT MUST BE EARTHED

IMPORTANT:
Your equipment is supplied with a mains lead, the wires of which are colored in

accordance with the following code: Green and Yellow   Earth, Blue   Neutral,

Brown   Live.

Green   Yellow

to Earth

Brown to Live

Fuse

Blue to Neutral

Cord Clamp

As the colors of the wires in your mains lead in this equipment may not correspond with
the markings identified with the terminals of your plug, proceed as follows:

The wires which are colored Green and Yellow must be connected to the terminal in the

plug which is marked with the letter E or 

 earth symbol @or colored Green or

Green and Yellow.

The wire which is colored Brown must be connected to the terminal which is marked with
the letter L or colored Red.

The wire which is colored Blue must be connected to the terminal which is marked N or

colored Black.

The plug moulded onto the cord incorporates a fuse. For replacement, use a 5 amp

BS1362 fuse. Only ASTA approved fuses should be used. The fuse cover/carrier must be
refitted when changing the fuse. In the event of losing the fuse cover/carrier, the plug
must not be used until a replacement has been obtained from your nearest electrical

 and fitted. the color of the fuse cover/carrier is that of the colored marks on the

insert in the base of the plug.

Summary of Contents for CM2096ME





















Reviews: