10
3
After pulling out the end with marking
“ ”
(right) of the water
drainage hose from the right groove of the unit, the end with
marking
“ ”
(left) of the water drainage should be inserted
into the corresponding groove of the left unit.
把排水管刻印文字“ ”(右)標記部從機體右側的凹槽內引出，
刻印文字“ ”（左）標記部應嵌入機體左側對應的凹槽內。
4
The water drainage hose should be pulled out through the proper
hosere tainer when the hose is pulled out on the left.
排水管從左面引出時，排水管應通過相應的軟管固定夾後再引出。
2
Inserts in the scoop channel with screwdriver,loosens the hose clamp.
用一字螺絲刀插入凹槽內，鬆開軟管固定夾。
※
Advert: the screwdriver please don't bump into the hose.
※注意：螺絲刀請勿碰到軟管。
How to Install the Water Drainage Hose
■
The water drainage hose is installed at the factory on the right side. It can be moved to the
left side if necessary.
1
Lay the unit down slowly.
• Lay the unit down on some corrugate paper to
prevent damage.
2
Pull out the water drainage hose from the left
side of the unit.
1
Remove the left water drainage hose cover.
■
When
tting the water drainage hose to
the water drainage outlet
If the water drainage outlet is too shallow
or the end of the water drainage hose
touches the grounds, cut the end of the
water drainage hose in an oblique angle.
• Water drainage hose which inserts into the unit, can't
touch other parts, to prevent the damage caused by
water leakage.
The
“
”
(left) or
“
”
(right) mark of
the water drainage hose should be inserted
into the corresponding groove of the unit.
• Water drainage hose retainer must be tightened.
• The inner section of the water drainage hose must be
secured by the retainer before fetched out.
• Failure to do so may cause insuf cient
rinsing or unit malfunction due to
poor drainage or too much subbles
during rinsing and spinning.
Water drainage hose is pulled
out on the left
End with making “Left”
Water drainage
hose outlet
Water drainage hose
Water drainage outlet
Water drainage
hose cover
Corrugate paper
Front
Water drainage hose is pulled
out on the right
Lettering (right)
Water drainage hose outlet
排水管的安裝(
AJ-S75MX
)
產品出廠時，排水管安裝在機身右側，請視排水位置的具體情況將其換至左側。
請將機體輕輕地放倒。
放倒機體時，請在地面上放置一些瓦楞紙類的
襯墊，以免損傷機身。
排水管蓋
刻印文字
刻印文字
固定在排水管引出口（右）處時
固定在排水管引出口（左）處時
瓦楞紙
前側
排水管引出口
排水管從左面引出。
Water drainage hose cover
排水管蓋
排水管引出口
排水管
排水口
注意
安裝洗衣機時，請務必將排水管的刻印文字
標記部嵌入機體相對應的凹槽內。
排水管在機體內的部分，不應與其他部件碰觸，以免因
破損產生漏水而導致不必要的損失。
排水管固定夾必須夾緊。
排水管機內部分必須經固定夾固定後再引出。
排水管插入排水口時
排水口較淺或排水管前端與地面碰觸時，可
將排水管的前端沿斜向切除一部分。
若不切除，在漂洗及脫水時，由於排
水狀況的不良，將會引起漂洗不充分
或因肥皂沫而影響電機運轉。
Attention
4
將機體左面的排水管蓋拆下。
Hose retainer
軟管固定夾
4
Installation Guide (continued)
安裝指南（續）
※
This discharge pipe installs the method to be only suitable in AJ-S75MX.
此排水管安裝方法只適用於
AJ-S75MX
。
