background image

ENGLISH 

 

 

7

 

SAFETY INSTRUCTIONS (continued)

 

 

About the Symbols (continued) 

 

 

 

Be careful in moving the PDP TV

 

Neglect could result in an injury or damage. 
• Do not move the television during use. Before moving, disconnect the power plug and all external connections. 
• You are advised to move the television with two persons. 
• Avoid any impact or shock to the television; particularly take care of glass screen. 

Do not put anything on top of the PDP TV.

 

Placing anything on the television could result in loss of balance or falling, and cause an injury or damage. Use special 
caution in households where children are present. 

Avoid a humid or dusty place.

 

Placing the television in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical 
shock. 
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity. 

Avoid a high temperature environment.

 

The heat could have adverse influence on the television and other parts, and could result in transformation, melting or 
fire. 
• Do not place the television, the remote control and other parts in direct sunlight or near a hot object such as heater, etc. 
• Do not put the television in a place where the temperature is widely changing. 

Remove the power cord for complete separation.

 

• For safety purposes, disconnect the power cord if the television is not to be used for prolonged periods of time. 
• Before cleaning, turn off and unplug the television. Neglect could result in fire or electrical shock. 
 

 
 
 

Installation environment

 

Do not obstruct a ventilation hole. 
Do not put the television on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the 
television. Do not put the television in the following places. 
• Hot places such as near heater, place exposed to the direct rays of the sun. 
• A place where the temperature is widely changing. 
• Places with soot, dust or high humidity. 
• Poor air ventilation place. 
• Place near fire. 
• A wet place such as bathroom, or shower room. 
• Place where you can trip over it. 
• Always vibrating or strongly vibrating places. 
• Distorted or unstable places. 

How to view the PDP TV

 

If you use the television in too dark a room, your eyes may become tired. Please use it in a reasonably bright room. 
Avoid direct rays of the sun to the screen in order to prevent eye fatigue. Your eyes will get fatigued after viewing the television for 
long period of time. Relax your eyes by viewing away from the television from time to time. 
Please watch the television in downward direction. 
 

Note on image retention 

The plasma PDP TV illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of 
illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the 
screen as grayed-out images. 
Tips to prevent such image retention are: 
• Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and   
  graphic patterns, for long. 
• Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them  
  using screen saver function. 
• Turn down the contrast and brightness controls.

 

How to clean the plasma screen panel of the PDP TV

 

Before cleaning the television, turn off the television and disconnect the power plug from the power outlet. 
To prevent scratching or damaging the LCD screen face, do not knock or rub the surface with sharp or hard objects. Clean the 
screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. 
Do not use harsh or abrasive cleaners. 

How to clean the cabinet of the PDP TV

 

Use a soft cloth to clean the cabinet and control panel of the television. When excessively soiled dilute a neutral detergent in water, 
wet and wring out the soft cloth and afterward wipe with a dry soft cloth. 
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. 
especially because they would cause discoloration, scratches or cracks. 

CAUTION 

PRECAUTIONS 

Disconnect the 

plug from the 

power outlet.

HITACHI MODEL 42PD6000TA 

Summary of Contents for 42PD6000TA











































Reviews: