background image

 

30

9. Wiring Block Diagram   

 

 

Item 

No. 

Wire 

Part No. 

HITACHI Part No.

Item 

No. 

Wire 

Part No. 

HITACHI Part No.

Item

Board 

Part No. 

HITACHI Part No.

P205  Wire Ass’y W10/10P 

E057410010 

TE02294 

12 

P207  FFC 50P+AI 

E784650506 

TE02751 

IR Board(PWB-0874) 

5097659801 TE03511 

P203  Wire Ass’y W11/10P 

E057411001 

TE02292 

13 

P212  Wire Ass’y W5/5P 

E057405011 

TE02299 

RS-232 Board(PWB-0832) 

5097643008 

TS06665 

P201  Wire Ass’y W2/2P 

E057402005 

TE02291 

14 

P9001A  Wire Ass’y W8/8P 

E057408006 

TE02304 

Power/EMI Board(PWB-0905) 

5097651912 

TS06667 

P208  Wire Ass’y W9/9P 

E057409002 

TE02296 

Wire Ass’y W4/4P 

E057408005 

Audio Power Board(PWB-0905) 

5097651913 

TS06666 

P9003A  Wire Ass’y W4/4P 

E057404011 

TE02305 

15 

P7002A 

(This wire is 

included in PCB-Key pad assembly)

 H 

Audio 

Board(PWB-0807) 

5097639914 

TS06668 

P211  Wire Ass’y W5/5P 

E057405008 

TE02298 

16 

P215  Wire Ass’y   

E057401009 

TE02753 

Speaker Connector Board(PWB-0906) 

5097653206 

TS06671 

P814  Wire Ass’y W3/3P 

E057403016 

TE02755 

17 

P206  Wire Ass’y W20/20P E057420004  TE02295 

HDMI 

Board(PWB-0892) 

5097652105  TS06669 

P813 

Wire Ass’y W3/2P 

E057403015 

TE02754 

Item 

Board 

Part No. 

HITACHI Part No.

K Tuner 

Module 

5052110027 

TE03601 

P811  Wire Ass’y   

E057401008 

TE02761 

Main Board(PWB-0891)

5097652009 

TE04071 

Power Module 

6693006618 

TS06011 

10 

P209  Wire Ass’y W4/4P 

E507404009 

TE02297 

I/O Board(PWB-0899) 

5097651805 

TS06662 

ATSC Connector Board(PWB-0833) 

5097642804 

TS05977 

11 

P204  Wire Ass’y W31/30P 

E057431012 

TE04091 

Key Pad(PWB-0874) 

5097659800 TE03501 N ATSC 

Module 

5053911108 

TS07471 

Summary of Contents for 42HDF39














































Reviews: