background image

 

 

2

IMPORTANT SAFETY INSTRUCTIONS 

                                                 

 

 

 

 

 

 

 

 

 

 

 

 

 

                                                                                 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15. Televisions are designed to comply with the recommended
safety standards for tilt and stability. 
Do not apply excessive pulling force to the front, or top, of the 
cabinet which could cause the product to overturn resulting in 
product damage and/or personal injury. 
16. Follow instructions for wall, shelf or ceiling mounting as 
recommended by the manufacturer. 
17. An outdoor antenna should not be located in the vicinity of 
overhead power lines or other electrical circuits. 
18. If an outside antenna is connected to the receiver be sure 
the antenna system is grounded so as to provide some 
protection against voltage surges and built up static charges. 
Section 810 of the National Electric Code, ANSI/NFPA No. 
70-1984, provides information with respect to proper grounding 
for the mast and supporting structure, grounding of the lead-in 
wire to an antenna discharge unit, size of grounding connectors, 
location of antenna-discharge unit, connection to grounding 
electrodes and requirements for the grounding electrode. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Note to the CATV system installer: This reminder is provided to 
call the CATV system installer’s attention to Article 820-40 of the 
NEC that provides guidelines for proper grounding and, in 
particular, specifies that the cable ground shall be connected to 
the grounding system of the building, as close to the point of 
cable entry as practical. 

Read before operating equipment 

Follow all warnings and instructions marked on this television.
1. Read these instructions. 
2. Keep these instructions. 
3. Heed all warnings. 
4. Follow all instructions. 
5. Do not use this apparatus near water. 
6. Clean only with a dry cloth. 
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions. 
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that 
produce heat. 
9. Do not defeat the safety purpose of the polarized or 
grounding-type plug. A polarized plug has two blades with one 
wider than the other. A grounding type plug has two blades 
and a third grounding prong. The wide blade or the third prong 
are provided for your safety. If the provided plug does not fit 
into your outlet, consult an electrician for replacement of the 
obsolete outlet. 
10. Protect the power cord from being walked on or pinched 
particularly at plugs, convenience receptacles, and the point 
where they exit from the apparatus. 
11. Only use the attachments/accessories specified by the 
manufacturer. 
12.            Use only with the cart, stand, tripod, bracket,
               or table specified by the manufacturer, or 
               sold with the apparatus. When a cart is used,
               use caution when moving the cart/apparatus
               combination to avoid injury from tip-over. 
13. Unplug this apparatus during lightning storms or when 
unused for long periods of time. 
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any 
way, such as power-supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into apparatus, the 
apparatus has been exposed to rain or moisture, does not 
operate normally, or has been dropped.   

This product contains lead. Dispose of this product in accordance with applicable environmental laws. For product recycling and 
disposal information, contact you local government agency or the Electronic Industries Alliance at www.eiae.org (in the US) or the 
Electronic Product Stewardship Canada at www.epsc.ca (in Canada). For more information, call “1-800-HITACHI.” 

Do not place any objects on the top of the television which may fall or cause a child to climb to retrieve the objects.

 

PREVENTION OF SCREEN BURN 

Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed 
(nonmoving) patterns can cause permanent damage to television receivers. Such “SCREEN BURNS” constitute misuse and are 

NOT

 

COVERED 

by your HITACHI Factory Warranty. 

PUBLIC VIEWING OF COPYRIGHTED MATERIAL 

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require 
prior authorization from the broadcaster or owner of the video program material.

• 

This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a 

cable system providing such programming. A CableCARD provided by your cable operator is required to view encrypted digital programming. 
Certain advanced and interactive digital cable services such as video-on-demand, a cable operator’s enhanced program guide and data-enhanced 
television services may require the use of a set-top box. For more information call your local cable company. 
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this 
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only 
unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. 

Summary of Contents for 42HDF39



















































Reviews: