background image

 

 
Specific Absorption Rate (SAR) information: 

 

This Tablet POS meets the government's requirements for exposure to radio waves. 
The guidelines are based on standards that were developed by independent scientific 
organizations through periodic and thorough evaluation of scientific studies. The 
standards include a substantial safety margin designed to assure the safety of all 
persons regardless of age or health. 
 
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 
W/kg averaged over one gram of tissue. Device types: Tablet POS 
(FCC ID: 

) has also been tested against this SAR limit. The highest 

SAR value reported under this standard during product certification for use at the 
properly worn on the 

body is 0.612W/kg

. This device was tested for typical 

body-worn operations with the back of the handset kept

 

00cm

 from the body. To 

maintain compliance with FCC RF exposure requirements, use accessories that 
maintain a 

00cm

 

separation distance between the user's body and the back of the 

handset. The use of belt clips, holsters and similar accessories should not contain 
metallic components in its assembly. The use of accessories that do not satisfy these 
requirements may not comply with FCC RF exposure requirements, and should be 
avoided. 
 

Body-worn Operation 

This device was tested for typical body-worn operations. To comply with RF exposure 
requirements, a minimum separation distance of 

0.0 cm

 

must be maintained between 

the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, 
and similar accessories used by this device should not contain any metallic components. 
Body-worn accessories that do not meet these requirements may not comply with RF 
exposure requirements and should be avoided. Use only the supplied or an approved 
antenna. 
 
 
 
 
 
 
 
 
 
 
 
 

GQK-HM516

Summary of Contents for HM516









Reviews: