manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 116 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 116

108

Using the Switched Probe

7.8  Using the Switched Probe

The optional switched probe enables the start and stop operations of the ST5520/

ST5520-01 while the probe is held in hand.

Before a test, set the push switch mode to either trigger (

[TRIG]

) or continuous 

(

[CONT]

). It is initially set to continuous mode (

[CONT]

).

1

 

Open the Settings screen.

Select 

[SET]

.

2

 

Select the operation mode for 

[EXT.SWITCH MODE]

.

Selection

[CONT]

[TRIG]

Return to the 
Measurement 
screen.

[CONT]

(Continuous mode)

A test is performed only when the push switch is pressed.
When the push switch is released, the test is terminated.

[TRG]

(Trigger mode)

Press the push switch to start a test. The test continues 
even when the push switch is released. When the push 
switch is pressed during the test, the test is terminated.

 

• For the operation of the ST5520 and ST5520-01 when the switched probe is 

used, refer to “Enabled/disabled input list” (p. 163).

 

• The 9299 Switched Probe can be used as an ordinary probe when the switch 

signal line plug is not connected to the EXT.SW terminal.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments