Hioki ST5520 Instruction Manual Download Page 171

Page: 171 / 201

163

Key combination

Initialization (Turn on the power while pressing the

MENU

+ Up keys.)

Interlock cancellation (Turn on the power while pressing the

MENU

Down keys.)

Enabled/disabled input list

The following table shows the status (enabled/disabled) of the keys, switched probe, EXT.I/O,

and RS command input. “



” indicates enabled and “-” indicates disabled. Some combinations of

status can occur simultaneously, however, the disabled status has priority.

Input

Status

Key input

Switched

Probe 9299

START

STOP

UNLOCK/LOCAL

Others

START/STOP

The EXT.I/O STOP signal

is LOW.

−



−

The EXT.I/O INTERLOCK

signal is LOW.

−



−

Remote

−



(Resets the remote.)

−



Key lock



(Resets the lock.)

−



TEST

−



−



Input

Status

EXT.I/O

RS command

START

STOP

Others

:START

:STOP

Others

The EXT.I/O STOP signal

is LOW.

−



−

Execution

error



The EXT.I/O INTERLOCK

signal is LOW.

−



−



Remote



Key lock



TEST

−



−

Execution

error



: The interlock is enabled during panel load operation.

: The test is stopped when panel is loaded during the test.

: Some commands stop a test.

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Search results

Summary of Contents for ST5520

Reviews:

Hioki ST5520, Instruction Manual, Page: 171 / 201

Search results

Summary of Contents for ST5520

Reviews: