manualshive.com logo in svg

Hioki MR8827, Instruction Manual

Share
Download
Hioki MR8827 Instruction Manual Download Page 319

314

LAN Connection and Settings (Before Using FTP/Internet Browser/Command Communications) 

2. Make a 

1:1 Connection Between the Instrument and a PC

(Connect the Instrument to a PC)

You can monitor and control the instrument from a PC by connecting the instrument to the PC with 

a LAN cable (100BASE-TX cable)

 • Connection cable:  Use one of the following.

 • 100BASE-TX crossover cable (maximum length 100 m)

 • 100BASE-TX straight-through cable (maximum length 100 m)

 •

9642 LAN Cable (optional, supplied with crossover adapter)

This completes the connection procedure.

Files on the instrument can now be accessed from the PC.

Refer to “16.2 Perform Remote Operations on the Instrument (Use an Internet Browser)” (p. 315), “16.3 

Access Files on the Instrument From a PC (Using FTP)” (p. 322), or “16.7 Controlling the Instrument with 

Command Communications (LAN/USB)” (p. 333).

If there is a possibility of interference from other equipment in the vicinity, wind the 

LAN cable once around the supplied ferrite clamp-on choke (for LAN/USB cable), as 

shown in the illustration at right.

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands