manualshive.com logo in svg

Hioki MR8827, Instruction Manual

Share
Download
Hioki MR8827 Instruction Manual Download Page 257

252

FFT Analysis Condition Settings

13.3.7 

Average Analysis Results (Waveform Averaging)

The averaging function calculates the average of the values obtained from multiple measurements of a 

periodic waveform.

This can reduce noise and other non-periodic signal components. Averaging can be applied to a time-

domain waveform or to a spectrum.

Procedure

Press the 

STATUS

 key to open the Status screen, and then select the 

[Status]

 sheet.

1 

Enable averaging.

Move the cursor to 

[Average]

.

Off

Averaging is disabled.  

(Default setting)

Linear (Time 

axis)

Time-domain waveforms are summed and 

averaged and then calculation is performed.

Expo. (Time 

axis)

The exponential mean of time-domain 

waveforms is determined and then calculation 

is performed.

Linear 

(Frequency)

Frequency-domain waveforms are summed 

and averaged and then the calculation result 

is output.

Expo. 

(Frequency)

The exponential mean of frequency-domain 

waveforms is determined and then the 

calculation result is output.

Peak 

(Frequency)

The maximum value of frequency-domain 

waveforms is retained.

1

2

About averaging calculation 

formulas

Refer to “Averaging” (p. A19).

When averaging and auto-saving 

or auto-printing are enabled at the 

same time

Data is saved or printed after the 

specified number of values has been 

averaged.

Refer to “Trigger Modes and Averaging” 

(p. 254).

2 

Select the count for averaging.

Move the cursor to 

[Number]

.

Select the number of measurements to be averaged.

Setting range:   2 to 10,000

 • After measuring with averaging enabled, display is not available when the channel is changed. Also, 

when the analysis mode is changed, the analysis modes that can be displayed are limited.

 • When averaging is performed with analysis mode disabled (Off), no trace will be displayed when the 

analysis mode is changed after measurement.

 • When 

[Format]

 is set to 

[Running spectrum]

, 

[Average]

 cannot be used.

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands