background image

1

Introduction

Introduction

Thank you for purchasing the Hioki IR4055-11, IR4056-20, 
IR4056-21, IR4057-20, IR4058-20 Insulation Tester. To obtain 
maximum performance from the instrument, please read this 

Instruction Manual first, and keep it handy for future reference.
Hereinafter, the descriptions refer to models without the suffix.

Verifying Package Contents

When you receive the instrument, inspect it carefully to ensure that no 
damage occurred during shipping. In particular, check the accessories, 
panel switches, and connectors. If damage is evident, or if it fails to 

operate according to the specifications, contact your authorized Hioki 
distributor or reseller. Confirm that these contents are provided.

Insulation Tester
IR4055, IR4056

IR4057, IR4058

Instruction Manual

LR6 Alkaline battery × 4

Model L9787 Test Lead*

(Only for the instruments with suffix 

“-20”)

Model L9788-11 Test Lead Set with 

Remote Switch* 

(Only for the instruments with suffix “-11” 

and “-21”)

Neck strap

*  Model L9787 and L9788-11 are all exclusively designed for the Hioki IR4000 

series. Do not use for any other purpose.

1

2

3

4

5

6

7

付録

索引

Summary of Contents for IR4055



















































































Reviews: