Hino 238 Workshop Manual Download Page 57

Page: 57 / 919

ENGINE CONTROL SYSTEM (J08E)

4–834

DTC: P1428

EN01H16F01030F03001106

P1428: Differential pressure sensor - out of range (Out of range high)

INFORMATION

1. Technical description

•

It detects a difference between pressure at the inlet of the muffler and atmospheric pressure and monitors any failure
or malfunction of the DPR.

<Description of malfunction>

•

Exhaust pressure cannot be correctly recognized.

•

Possible DPR differential pressure sensor failure or hB short

2. DTC set condition

(1) Check conditions

•

Starter switch ON.

•

Battery voltage is in the range of 10 V to 16 V.

The conditions described above remain for 5 seconds or longer.

(2) Judgement criteria

•

Output of the sensor remains greater than 4.46 V (95.1 kPa {13.8 psi}) for 3 seconds.

3. Reset condition

•

Immediately after normal operation is restored.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

(ET4+)

(ET2+)

(EXPS)

(ADG9)

(AVC5)

LCG

KR4

(GND3)

(TEX3)

KUH

LCT

KUQ

OUT)

(GND)

KSK

KSL

(VCC)

KSJ

LCY

LCZ

LCY

LCG

KSF

LCT

KSK

KUH

KSJ

KUQ

KSE

KR4

LCY

LCG

KSF

LCT

KSK

KUH

KSJ

KUQ

KSE

KR4

(GND1)

(TEX1)

KSE

KSF

Exhaust gas
temperature
sensor
(DOC outlet)

Exhaust gas
temperature
sensor
(DOC inlet)

Differential
pressure
sensor

Engine

ECU

SAPH16F010300665

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands