Hino 238 Workshop Manual Download Page 111

Page: 111 / 919

ENGINE CONTROL SYSTEM (J08E)

4–888

DTC: P14BF

EN01H16F01030F03001114

P14BF: EGR valve controller temperature sensor 1, 2 - rationality (EGR actuator temp.
sensor 1 performance invalid)

INFORMATION

1. Technical description

•

EGR valve is a butterfly type.

•

EGR valve opening is controlled by engine speed and amount of intake air.

•

EGR valve opening is adjusted by engine ECU and CAN communication.

•

EGR valve will not operate when engine coolant temperature is low (

≤



C {104



F})

•

Wiping operation from "fully open



fully closed" is conducted as an EGR valve surface cleaning operation when the

starter switch is LOCK.

<Description of malfunction>

•

Failure message is received from EGR controller.

2. DTC set condition

(1) DTC detection condition

•

Battery voltage is in the range of 8 V to 16 V.

•

There is no disconnection in harness connected to EGR valve.

•

Starter switch ON. (Not related to engine speed.)

(2) Judgement criteria

•

When temperature of temperature sensor 1 inside actuator is between -20



C {-4



F} and 170



C {338



F}, and

difference between temperature sensors 1 and 2 is at least 30



C {86



F}, this condition continues for 1 second.

3. Reset condition

•

Immediately after normal operation is restored.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

VNT
controller

VNT
actuator

ENG No.1 SUB W/H

ENG No.1 W/H

LM8

(AMPU)

LMY

LMZ

(HSPW)

(MPU)

LM4

(AHOU)

LM3

(AHOV)

(HOV)

LM2

LMU

(AHOW)

(HOW)

%KQ

(ENG)

%KV

(VNTC)

%KW

(VNTA)

LM5

LMW

LMV

(AHSG)

(SLGD)

(HSGD)

LM1

LMX

(AHSP)

(AMPW)

(AMPV)

LMT

(MPV)

LM0

(MPW)

KV0

(VNTV)

(VNTG)

KV8

(VNTH)

KV9

(VNTL)

L4T

(EGR

L4U

(EGRG)

L4S (EGRL)

L4R (EGRH)

(CANH)

K6W

K6V

(CANL)

(HOU)

LMS

LM4

LMS

LM3

LMT

LM2

LMU

%Z3

LMW

LM5

LMV

LM1

LMX

LM8

LMY

LM7

LMZ

LM6

LM0

LM7

LM6

%Z3

(ENG)

CAN circuit (DPR) (BA-1)

EGR

controller

Engine

ECU

(BA-1)

To CAN circuit (DPR)

EGRL

L4S

EGRH

L4R

EGRV

L4T

EGRG

L4U

SAPH16F010300702

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands