manualshive.com logo in svg

Hinkley Tier, Instruction Manual, Page: 6 / 21

Share
Download
Hinkley Tier Instruction Manual Download Page 6

UNPACKING YOUR FAN

UNPACK YOUR FAN AND CHECK THE CONTENTS.

 

 

04

 

|

 hinkley.com

TIER PACKAGE CONTENT

1

Blade Set of 5

2

Hanging Bracket

Blade support plates

3

Ceiling Canopy and Trim Ring 

4

5

6

7

8

9

10

11

12

13

14

1

6

14

3

5

8

10

9

2

11

12

13

• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing.
  Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.

• Examine all parts. You should have the following:

NOTE:

 Design of parts shown above may look slightly different for

your specific model of fan.

7

4

Downrod Asm.

Yoke cover

 

 

 

 

Mounting Plate

16W LED Assembly

Glass Shade

R6 wire nuts

Hardware Bag

Ball Moisture Cover

Fan Housing with Motor
*Remove rubber shipping 
supports around motor, if 
applicable. Save the screws.

Wall Control w/12v Battery

Bracket Mounting Hardware
(wood screws, screws, lock
washers, washers, wire nuts), 
Blade to Motor Screws
w/Lock Washers,
Balance Kit 

Summary of Contents for Tier






















Reviews:

No comments